Should It Take a 14oz Cartridge To Fill Trailer Hub
Question:
After reading On how to grease a Dexter EZ Lube Axle Wanting to put in fresh grease in our Never-R-Adjust Dexter EZ Lube Axle on our RV, I put in a fresh 14oz grease cartridge, attached the grease gun to the zerk and started rotating the tire while squeezing the handle on the manual grease gun. After about 5 minutes or more, I was still not seeing any grease exit the front or sides of the spindle and then I ran out of grease. So, I left that side and went to the other side of the trailer. I put in a new grease cartridge and started the process as in the Dexter video of greasing that side. Again, it took about 5 or more minutes while rotating the wheel continuously and again I ran out of grease. So, about 14 oz in that side as well and never saw any grease coming out from around the front of the spindle. I then called Jayco and they didn’t have any information on the axle and they referred me to my Jayco dealer. I called that dealer and told him what had taken place and immediately he said I likely blew the rear seals and the grease was likely in the brake housing! At this point, I phone Dexter tech support and held on line for about hour. While I was on hold, I saw the text option available and started a text with someone in Dexter Tech support. The text support comments: Me: I put a full tube of grease in both sides and never saw any grease coming out the front or anywhere as per your diagram and video Dexter Tech: Were they completely dry prior to adding the grease? If so, it may take more than a tube before you see grease from the pin hole on the spindles side. Me: I dont know if they were completely dry prior to starting as this is a new trailer 2022 and the first time to lube. However, I didnt see any old or new grease come out the front so I have to assume it was near empty. If the EZ lube axle is working as the videos and diagram show then the grease should exit the front spindle side and not blow out the real seal as my dealer said might have happened. That is my only concern. If the axle cavities were just mostly empty and it could hold a tube of grease, then all is fine by me. I will have the axles repacked after the summer after my first year of owning it. Dexter Tech: You need to removed the hub/drum and take it apart to inspect it. What is your opinion on needing to remove the hub to check the rear seal or just that the axles took that much grease?
asked by: Johnny A
Expert Reply:
I honestly don't see how it's physically possible to pump a whole 14oz tube of grease into a single hub, especially when your trailer is only a year or two old.
Grease seals are notorious for blowing out the back of the hub which is why the EZ Lube spindle setup is nice but dangerous. I definitely recommend pulling your hub to check on the seals. If the seals blew (most likely) you're going to have grease on your brakes which will be rendered useless until you get it all cleared off and replace the rear seals.
To replace the seals you'll need one of the following based off of your axle weight capacity:
2K Axle - # 34823 (Qty 1)
3.5K Axle - # RG06-050 (Qty 2)
5.2K Axle - # RG06-070 (Qty 2) for 2.250" OD OR # GS-2125DL (Qty 1) for 3.376" OD
Hopefully this helps put your mind at ease. It's always better to be safe than sorry, especially when it comes to traveling on the road.
![Jon G](https://images.etrailer.com/static/images/catg/people/1086_tn.jpg)
Products Referenced in This Question
Grease Seal - Double Lip - 2.125" ID - 3.376" OD - GS-2125DL
- Trailer Bearings Races Seals Caps
- Seals
- Grease Seals - Double Lip
- 2.125 Inch I.D.
- 3.376 Inch O.D.
- etrailer
more information >
Grease Seal - Double Lip - ID 1.719" / OD 2.565" - for 3,500-lb Axles - Qty 2
- Trailer Bearings Races Seals Caps
- Seals
- Grease Seals - Double Lip
- 1.719 Inch I.D.
- 2.565 Inch O.D.
- etrailer
more information >
- Trailer Bearings Races Seals Caps
- Seals
- Grease Seals - Double Lip
- 2.250 Inch I.D.
- 3.376 Inch O.D.
- TruRyde
more information >
Product Page this Question was Asked From
Double Lip Grease Seal - ID 1.249" / OD 1.983" - Qty 1
- Trailer Bearings Races Seals Caps
- Seals
- Grease Seals - Double Lip
- 1.249 Inch I.D.
- 1.983 Inch O.D.
- TruRyde
more information >
Continue Researching
- Article: Most Popular Wheel Bearings
- Q&A: Possible Bearing Buddy that Could Fit Hub with Seal 12194TC
- Q&A: Replacement Trailer Hub Seal for TCM 12194TC
- Article: Replacing the Bearing, Races and Seals on a Trailer Hub
- Q&A: How to Tell if Trailer has a BT8 or BTR Spindle Installed
- Q&A: What Is the Difference Between a BTR and BT8 Spindle
- Article: Parts Needed to Add Electric Drum Brakes to a Trailer
- Q&A: What is The Outer Diameter of The Dexter Trailer Idler Hub Assembly # 8-258BTUC1?
- Q&A: Replacement Grease Seal 4410275 For Shoreland'r Boat Trailer
- Q&A: Replacement Grease Seal for GS-1250DL
- Article: How to Measure Your Trailer Wheel Bolt Pattern
- Article: Tire TLC: How & When to Check Your RV/Trailer Tire Pressure
- Article: Trailer Tire Sizing
- Article: Trailer Wiring Diagrams