Can Trailer Brakes be Added to 3,500 lb Trailer Axle that Doesn't Have Brake Flanges
Question:
I have single axle 3500 lb Carry-On trailer I want to add brakes but trailer doesn’t have the four hole mounting bracket for the brake assembly. Is there a way to put brakes on it without brackets and if not is there a way to put brackets on it? Any input would be appreciated. Thanks.
asked by: Eric
Helpful Expert Reply:
You can have brake flanges welded to your current 3,500 lb axle spindles with the part # 4-35 and you'd then be able have brakes assemblies bolted on.
For 3,500 lb axles you will use 10 inch assemblies. My recommendation is the Electric Trailer Brake Kit - Self-Adjusting - 10" - Left and Right Hand Assemblies - 3,500 lbs # AKEBRK-35-SA for each axle. These won't every require adjustments so I recommend them highly. Then I recommend using the Trailer Hub and Drum Assembly - 3.5K E-Z Lube Axles - 10" Diameter - 5 on 4-1/2 - Pre-Greased # AKHD-545-35-EZ-K.
Products Referenced in This Question
etrailer Electric Trailer Brakes - Self-Adjusting - 10" - Left/Right Hand Assemblies - 3.5K
- Trailer Brakes
- Electric Drum Brakes
- Standard Grade
- Self Adjust
- 10 x 2-1/4 Inch Drum
- 3500 lbs Axle
- etrailer
more information >
Easy Grease Trailer Hub and Drum Assembly for 3.5K Axles - 10" - 5 on 4-1/2 - Pre-Greased
- Trailer Hubs and Drums
- Hub with Integrated Drum
- Easy Grease
- EZ Lube
- Pre-Greased
- L68149
- L44649
- For 3500 lbs Axles
- 1/2 Inch Stud
- 5 on 4-1/2 Inch
- 13 Inch Wheel
- 14 Inch Wheel
- 14-1/2 Inch Wheel
- 15 Inch Wheel
- etrailer
more information >
Product Page this Question was Asked From
Brake Mounting Flange for 2-3/8" Round Axle
- Accessories and Parts
- Trailer Brakes
- Disc Brakes
- Electric Drum Brakes
- Hydraulic Drum Brakes
- Brake Mounting Flange
- 10 Inch
- 2-3/8 Inch Diameter Axle
- Redline
more information >
Continue Researching
- Shop: Brake Controller
- Shop: Hayes Engage Trailer Brake Controller - 1 to 3 Axles - Time Delayed
- Shop: Brake Mounting Flange for 2-3/8" Round Axle
- Shop: Demco Trailer Brake Mounting Flange - 4 on 4-13/16" Bolt Pattern - 3" Pilot Hole
- Q&A: How to Find the Correct Brake Mounting Flange
- Q&A: How To Determine What is Needed To Add Electric Brakes To Enclosed Trailer
- Q&A: Are Specs Available for Welding on a Brake Mounting Flange to a Trailer Spindle
- Q&A: Recommendation for Installation of a Brake Mounting Flange on a Trailer Spindle and Axle
- Q&A: Determining the Axle Capacity of a 2 Inch Square Trailer Axle
- Q&A: Recommendation For Replacement For Brake Mounting Flange
- Q&A: Trailer Brake Mounting Hole Pattern is Not the Same as Drum Bolt Pattern
- Search Results: brake controller
- Video: etrailer Trailer Brake Controller Universal Kit Review
- Article: Brake Controller Installation: Starting from Scratch
- Article: How to Install a Brake Controller on Chevrolet / GMC 1999-2006 Pickups
- Shop: Tekonsha Prodigy P3 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Video: Choosing the Right Brake Controller
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Shop: Trailer Hitch
- Search Results: trailer brake controller
- Article: Trailer Wiring Diagrams
- Shop: Trailer Wiring
- Shop: Redarc Tow-Pro Liberty Brake Controller - Dash Knob - 1 to 2 Axles - Proportional
- Shop: Suspension Enhancement
- Search Results: etbc7
- Video: Tekonsha Prodigy P3 Trailer Brake Controller Review
- Shop: Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Search Results: redarc
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Video: Choosing the Right Trailer Wiring