Ground Clearance Dimensions for B and W Tow n Stow BW29FR

Question

Question:

Can you tell me how low the hitch is in inches from the part that slides in the receiver?

asked by: James M

0

Expert Reply:

The distance from the bottom of the shank of the B and W Tow n Stow part # BW29FR to the bottom of the ball mount is right at 7-3/4 inches. Worth nothing is that B and W states you need 11 inches of clearance from the bottom of your hitch to the ground to use this.

expert reply by: Jameson C

0

Answer 1

10 inches of ground clearance from the bottom of your B and W Tow n Stow to the ground is pretty low. I would highly recommend going with the version of your ball mount with 2-1/2 inches of drop instead with the part #BW44FR which would give you 12…

view full answer...

Answer 2

The RAS and air bag kits provide the same basic function of additional support to tow a trailer level like what you are doing and they both are adjustable but in general the ride quality of the RAS systems is much nicer than air bags so they are…

view full answer...

Answer 3

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

There's not many differences between the Air Lift WirelessONE item #AL25980EZ and item #AL25980. The main difference is that the item #AL25980EZ has a slightly higher CFM at 1.03 compared to 0.92 and it runs slightly more efficient at 9% over 15%…

view full answer...

Answer 8

A 2023 Chevy Silverado 1500 will need to have 4WD and a two-speed transfer case, which will need to be placed in neutral, in order to safely flat tow. Your owner's manual will have a list of instructions to follow to switch your transfer case…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

Because the Retrax PRO MX Tonneau Cover #RT80467 for the 2019 Chevy Silverado 2500 covers the bed rails, you would not be able to use a ladder rack like the Thule TracRac #TH27000XT since that rack requires the use of the bed rails. The only tonneau…

view full answer...

Answer 11

Mixing and matching the brackets and air springs isn't really recommended but you might be able to get a combination to work. If I were you I would just put the complete #AL88288 kit on since that would fit properly and there wouldn't be any…

view full answer...

Answer 12

Hey Brian, so according to TorkLift they don't have any tie downs for the front but for the rear you are going to want the TorkLift Camper Tie-Downs #TL54FR. Since your truck has factory running boards that extend under the bed, there aren't…

view full answer...

Ground Clearance Dimensions for B and W Tow n Stow BW29FR

Product Page this Question was Asked From

Continue Researching