Recommended Spare Tire Mounting Plate for Trailer Stake Pockets

Question

Question:

Looking for a spare tire mounting plate w/bolts as a part to the spare tire carrier made by Demco. I can send a picture of what I need, but do not need the part that mounts to the trailer only the part that the spare tire mounts to. The part looks the same on DM15851, DM15851, DM15853, and DM15854.

asked by: Richard P

0

Expert Reply:

The closest thing we have to what you're describing is the Demco Trailer Stake Pocket Spare Tire Carrier item # DM15850-76. It is also available in silver item # DM15850-52.

expert reply by: Jerred H

0

Answer 1

The Demco Trailer Stake Pocket Spare Tire Carrier w/ 4" Offset - Silver #DM15884-52 gives you the 4 inch measurement, so you just need to look at the width of your wheel. Most trailer wheels have a zero offset so the width of the tire itself…

view full answer...

Answer 2

Yes, the Demco Trailer Stake Pocket Spare Tire Carrier #DM15884-52 will fit with rub rails on stake pockets. I have included a image showing the bracket mounted on this type of trailer. The bracket has a 4" offset so you will need to measure…

view full answer...

Answer 3

Thank you for your purchase of the Demco Channel Tongue Trailer Coupler - eZ-Latch. The diameter is 5/16" and the lock that is designed specifically for Demco couplers with the eZ-Latch is the following: - InfiniteRule Lock for Demco eZ-Latch…

view full answer...

Answer 4

The distance between the bolts of the Demco Spare Carrier part #DM15850-52 that hold it to the stake pocket of the trailer is 4-5/8 inches.

view full answer...

Answer 5

I have attached a sheet which shows the torque specs for wheels you can use when putting a tire and wheel. For 1/2" wheel bolts on a 13" aluminum wheel the torque is 75-85 ft.-lb. For lug nuts you can use the Lionshead Trailer Wheel Lug Nut…

view full answer...

Answer 6

I would agree it is a little odd the Demco Spare Carrier part #DM15884-52 does not come with lug nuts but you'd just need the 1/2-20 size like the part #LHLR103.

view full answer...

Answer 7

To verify if your 2021 Ford E-450 cutaway chassis for your Class C motorhome is pre-wired for a brake controller you will need to remove the storage slot in the top of your dash. I have included a install video below that shows how to remove the…

view full answer...

Answer 8

I'm assuming your 2024 F-250 has the 6-3/4' bed. If that is correct, the right tie-downs are in fact the #TLF3008 and #TL77CR. TorkLift has accounted for the bed access steps on the 2024 model and confirmed these will fit your truck.

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

Since you are pulling a trailer that weighs around 8,500 lbs. you would just want to stick with the Firestone Ride-Rite Air Helper Springs #F35FV (5,000 lb.). You really only need to spend more for the Firestone Ride-Rite Red Label Extreme Duty Air…

view full answer...

Answer 12

Hey Beatrice, To find the right fit for your trailer's suspension you'll need to take a quick measurement of your current shackle straps. You'll need to measure from the center of one bolt hole to the center of the other bolt hole. The…

view full answer...

Recommended Spare Tire Mounting Plate for Trailer Stake Pockets

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching