Tools Needed To Replace 12,000LB Equal-i-zer Hitch Ball On Weight Distribution Hitch
Question:
2-5/16inch Hitch Ball for Equal-i-zer Weight Distribution Systems - 12,000 lbs Item # EQ91-00-6120 I have a 2018 Ford F250 Diesel 6.7L Powerstroke with Equalizer hitch set up currently to tow my 2019 International 30 ft Airstream. The set up is now 4 years old and the current hitch ball is showing signs of wear and I am thinking to have the ball replaced. Dealers and factory-trained locations are either booked for months or not accepting people for service unless they purchased the trailer at their location. I am full time so cannot leave my trailer at the shop. My question is do I need to have a factory-trained person remove the old hitch ball and install the new one or can I have it done myself? If the latter, then what are the specs for how to do it or have it done? Torque? Tools needed etc to have it done correctly / safely? Please advise. Thank you.
asked by: Michelle M
Expert Reply:
To replace your 2-5/16" Equal-i-zer Hitch Ball # EQ91-00-6120 you will need a Thin Wall Socket # EQ70-00-4800. You will also need a 3/4" drive ratchet, 6" extension, large crescent wrench and 3/4" torque wrench capable of 450 ft-lbs of torque. You will likely also need some penetrating oil to help remove the nut especially if you can see a lot of visible corrosion.
I have linked the installation instructions for the Equal-i-zer Weight Distribution System # EQ37120ET below so you will be able to go over all the torque specs for the hitch to ensure everything is till tightened correctly.
Products Referenced in This Question
Equal-i-zer Weight Distribution System w/ 4-Point Sway Control - 12,000 lbs GTW, 1,200 lbs TW
- Weight Distribution Hitch
- WD With Sway Control
- Some Sway
- Includes Shank
- Electric Brake Compatible
- Surge Brake Compatible
- Fits 2 Inch Hitch
- Allows Backing Up
- 1000 lbs
- 1100 lbs
- Equal-i-zer
more information >
Thin Walled Socket for Equal-i-zer Hitches
- Accessories and Parts
- Weight Distribution Hitch
- Tools
- Socket
- Equal-i-zer
- Equal-i-zer
more information >
Product Page this Question was Asked From
2-5/16" Hitch Ball for Equal-i-zer Weight Distribution Systems - 12,000 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 2-5/16 Inch Diameter Ball
- 2-1/4 Inch Shank Length
- 1-1/4 Inch Diameter Shank
- 12000 lbs GTW
- Class IV
- Class V
- Equal-i-zer
more information >
Featured Help Information
Instructions
Continue Researching
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: Are Spring Bars on Equal-i-zer Weight Distribution System Interchangeable?
- Q&A: Best Way to Prevent Sagging Suspension When Towing a Trailer
- Q&A: Tools Needed To Install etrailer Trailer Hitch Receiver On a 2019 Jeep Cherokee Trailhawk
- Article: Which Sway Control Hitch is Right For Your Trailer?
- Article: RV Propane 101: How Does My RV's Propane System Work?
- Q&A: How Does the Hopkins 7-Way part # HM40975 Wire to a Vehicle
- Q&A: Outer Diameter of Equal-i-zer Thin Walled Socket
- Q&A: Tools Needed To Install Fastway e2 Weight Distribution System
- Q&A: Changing a 14K Equal-i-zer Weight Distribution System to a 12K System
- Article: Towing a Trailer? Let's Talk About Brake Controllers
- Article: Determining Trailer Tongue Weight
- Article: Choosing the Right Suspension Kit for Your Truck and Trailer
- Article: Trailer Wiring Diagrams