Optronics Trailer Clearance Light Similar to AL 91RB that Installs With Smaller Hole Drilled
Question:
I am planning on using a red marker light to mount on my aluminum trailer for a rear side marker. Im considering getting the optronics a91rb with the a91bob mount. The mount will be flush to the surface. Will the right angle pigtail plug fit between the mounting surface and the light or protrude from the bottom requiring clearancing underneath. I would prefer to just drill a small hole for the wiring and not a large hole to clearance for the plug. It appears the other option is to get an al82rb and not use a right angle plug. Thanks for your assistance.
asked by: Trey E
Expert Reply:
The Optronics clearance light part # AL91RB in all of it's configurations would require a hole to be drilled for a harness like the part # A46PB to install with a grommet like the part # A91BOB. There isn't a way to mount it flush without drilling. If you used the part # AL82RB instead though it would require a much smaller hole be drilled since the entire harness of the other setup gets ran through the hole.
Products Referenced in This Question
Right Angle 2-Wire Pigtail for Optronics Trailer Lights - 2-Prong PL-10 Plug - 6" Lead
- Accessories and Parts
- Trailer Lights
- Wiring
- Plugs and Pigtails
- 6 Inch Long
- Two Wire
- Right Angle Pigtail
- Optronics
more information >
Mounting Bracket for Optronics A91, AL82, AL90, AL91, or AL191 Series Lights - Open Back - Black
- Accessories and Parts
- Trailer Lights
- Mounting Hardware
- Brackets
- Black
- Optronics
more information >
Thinline LED Clearance and Side Marker Light - Submersible - 3 Diodes - Rectangle - Red
- Trailer Lights
- Clearance Lights
- Rear Clearance
- Side Marker
- Rectangle
- Surface Mount
- Submersible Lights
- LED Light
- 2-1/2L x 1-3/16W Inch
- Red
- Optronics
more information >
Continue Researching
- Shop: Mounting Bracket for Optronics A91, AL82, AL90, AL91, or AL191 Series Lights - Open Back - Black
- Shop: Epicord 7-Way Molded Trailer Plug with Junction Box - 10' Long
- Shop: Tonneau Cover
- Shop: 3-Leaf Slipper Spring w/ Flat End for 2,900-lb Trailer Axles - 30" Long
- Shop: LaSalle Bristol Butyl Tape for XTRM RV roof membranes - 30' x 3/4" - Gray
- Shop: Black Molded Fender Bracket for MC65ARB and MCL65ARB Trailer Fender Clearance Lights
- Search Results: a67bb
- Shop: Rubber Grommet Mounting Kit for Peterson 2-1/2" Round Trailer Lights - Recessed Mount
- Search Results: a91bob
- Search Results: 68149
- Search Results: slipper spring
- Search Results: fender
- Search Results: license plate lights
- Search Results: tonneau covers
- Shop: Access TonnoSport Soft, Roll-Up Tonneau Cover
- Shop: Trailer Wiring
- Video: Review of TRC Enclosed Trailer Parts - 36279-955
- Shop: Vehicle Seat Covers
- Q&A: 7-Way and Junction Box Kit Recommendation for Trailer with 4-Way
- Video: etrailer A-Frame Trailer Coupler - Standard Coupler - CA-5400-Z Review
- Shop: Ladder Rack
- Video: Optronics Trailer Lights - Clearance Lights - MCL67RB Review
- Q&A: Clearance and Side Marker Light With Clear Lens and Red LEDs
- Q&A: Why is 10 or 12 Gauge Wire Recommended for Electric Brake Assemblies
- Q&A: What is the Depth of Optronics 2-Wire Pigtail?
- Q&A: Parts Needed to Install Optronics Submersible Red LED Clearance and Side Marker Light AL91RB
- Q&A: How to Establish Ground Connection When Re-Wiring Aluminum Trailer
- Q&A: Does The Optronics LED Side Marker Light # AL91AB have 2 Male Connector Posts
- Video: Optronics LED Clearance or Side Marker Light Review and Installation
- Video: Optronics Trailer Lights A86PB Review