No Brake Lights For Wiring Harness 118412
Question:
I installed my wiring harness from the car to the trailer but all I get is blinkers I dont get no brake lights and I dont get no tail lights
asked by: Danny
Expert Reply:
Thank you for your purchase from etrailer of Wiring Harness # 118412. If you are not getting no brake lights or no tail lights, the first thing to do is take a look at your owner's manual to locate any fuses or relays and ensure they are all there and in working order. If they are, in order to determine the specific problem you will need to purchase a circuit tester if you do not have one - the very handy Cordless Circuit Tester # PTW2979 - and test the connector on your vehicle after disconnecting it from your trailer. Check the wiring going into your harness from your tail lights to see if those wires are carrying the correct signals, if not then the issue is with the vehicle wiring.
If the signals going to your harness are okay, you'll need to test the signals coming out of the harness, and if they are correct then your issue is likely going to be with the trailer side wiring. You will also want to check both your vehicle and trailer connectors for corrosion, which can be green or white in color. A build-up of corrosion can interfere with the signals getting through the connectors so if it is present you are going to need to replace the plug with # 18004 for the trailer side. You'll also need to make sure your grounds are attached to bare metal surfaces and free of any paint, dirt or corrosion.
I have added links below to a pair of help articles on trailer wiring, including a troubleshooting guide for you to take a look at. Additionally, to help prevent any type of corrosion in your connector, and increase its durability and lifespan I highly recommend using Dielectric Grease for Electrical Connectors # 11755.
Products Referenced in This Question
Dielectric Grease for Electrical Connectors, 2 oz.
- Accessories and Parts
- Trailer Wiring
- Wiring
- Dielectric Grease
- LubriMatic
more information >
- Trailer Wiring
- Trailer Connectors
- Trailer End Connector
- 0 - 5 Feet Long
- Plug and Lead
- 4 Flat
- Draw-Tite
more information >
Product Page this Question was Asked From
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Powered Converter
- Custom Fit
- 4 Flat
- Tekonsha
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Q&A: 2024 Chevy Equinox Roof Rack Recommendation for a Bare Roof
- Article: My Trailer Hitch Doesn't Fit
- Article: Routing the Power Wire for a Trailer Wiring Harness
- Article: Wiring Trailer Lights with a 4-Way Plug (It's Easier Than You Think)
- Q&A: Installing Draw-Tite Class III Trailer Hitch on 2012 Toyota RAV4
- Q&A: Trailer Hitch Recommendation for 2011 Toyota RAV4
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: Does etrailer.com Hitch # E98864 Fit 2018 Toyota RAV4 Hybrid and Allow Handsfree Liftgate
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Q&A: How To Setup a 2007 Toyota RAV4 with 7-Way for Towing a Trailer with Brakes
- Article: How to Choose the Right Trailer Hitch Class
- Article: How to Choose a Bike Rack for an SUV or Crossover
- Article: How to Measure for Trailer Hitch Drop