Replacement Landing Gear Leg Options For a 2008 Keystone Montana With Legs Not Moving Under Load
Question:
I replaced the bevel gears in the lead leg on my 2008 Keystone Montana. I manually cranked the lead leg down to the same level as the follow leg. I then lowered the jack holding the trailer weight and the hydraulic unit would not raise or lower the landing gear. The hydraulic unit wanted to turn the shaft, but something was not letting that happen. They appeared to be jammed for some reason. A pin was stripped. I now have to remove the lead leg again and open it back up. Is there a problem with the screw jack inside the landing gear? I lowered it manually and it seemed fine. Only when I hooked up the hydraulic unit and put weight on the leg it did not work.
asked by: Jared B
Expert Reply:
It is possible the screw inside the Lead Leg # LC178653 on your 2008 Keystone Montana may be grooved in such a way that when weight is applied it creates to much resistance for the motor to turn the jacks. We do also carry the Follow Leg # LC178652 if you want to replace them both.
If you are thinking about replacing the jacks I recommend upgrading to the Ultra-Fab Deluxe Electric Landing Gear Set # UF17-943010. These each have their own motor which will allow you to operate the jacks individually on uneven ground. These jacks have a combined capacity of 12,000lbs which is much higher than your current landing gear. This would also eliminate any issue with the hydraulic unit not having enough power to raise/lower the jacks.
Products Referenced in This Question
Replacement Follow Leg for Keystone Montana 5th Wheel Landing Gear
- Accessories and Parts
- Camper Jacks
- Trailer Jack
- Legs
- Follow Leg
- Lippert
more information >
Ultra-Fab Deluxe Electric Landing Gear Set - 38" Lift - 12,000 lbs
- Camper Jacks
- Fifth Wheel Camper
- Leveling Jacks
- Stabilizer Jacks
- Steel
- 10001 lbs or More
- Electric Jack
- Landing Gear
- 38 Inch Lift
- Weld-On
- 2 Jacks
- Ultra-Fab Products
more information >
Product Page this Question was Asked From
Replacement Lead Leg for Keystone Montana 5th Wheel Landing Gear
- Accessories and Parts
- Camper Jacks
- Trailer Jack
- Legs
- Driver Leg
- Lippert
more information >
Featured Help Information
Instructions
Continue Researching
- Video: Review of Lippert Components - Trailer Jack,Camper Jack - LC178653
- Search Results: landing gear
- Search Results: landing gear parts
- Shop: Replacement Lead Leg for Venture 5th Wheel RV Landing Gear
- Shop: Replacement Lead Leg for Keystone Montana 5th Wheel Landing Gear
- Shop: Lippert Venture Lead Leg Repair Kit for 5th Wheel RV Landing Gear
- Q&A: Parts Needed to Rebuild Lippert Landing Gear Legs for Keystone Montana
- Q&A: Keystone Montana 5th Wheel Trailer Landing Gear Clicks and Wont Lift Trailer
- Q&A: Venture Landing Gear Repair Kit or Replacement Lead Leg
- Video: etrailer Landing Gear Set Review
- Shop: Trailer Hitch
- Shop: Landing Gear Set w/ Handle - 36-1/2" Lift - 8,000 lbs
- Search Results: hubs
- Video: Review of Lippert Components Camper Jack Parts - Landing Gear Lead Leg - LC119102
- Shop: Trailer Wiring
- Shop: Landing Gear Set - 36-1/2" Lift - 8,000 lbs
- Shop: Fifth Wheel Hitch
- Video: Review of Lippert Components - Trailer Jack,Camper Jack - LC146059
- Shop: Lippert Venture Follow Leg Repair Kit for 5th Wheel RV Landing Gear
- Video: Review of Lippert Components Power Landing Gear Repair Kit - LC146060
- Shop: Brake Controller
- Shop: Suspension Enhancement
- Shop: Gooseneck Hitch
- Shop: Lippert Components 32" Lead 5th Wheel RV Landing Gear Drop Leg w/Snap Pin
- Shop: Vehicle Tow Bar Brake System
- Q&A: Replacement Landing Gear for 2005 Montana 5th Wheel Trailer
- Q&A: How Do Tabs on Lippert LC178653 Landing Gear Leg Fit in Clips Welded onto 5th Wheel Frame
- Q&A: 2010 Keystone Montana 5th Wheel Replacement Landing Gear Components
- Q&A: Does Mounting Hardware Come with Replacement Landing Gear Gear Box RVLG-RDBOX
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)