Availability of Replacement Furrion Monitor and Side Cameras

Question

Question:

I have a 2019 356QB Forest River Hemisphere. It has a Furrion camera mounted in the rear. Do you have the viewer for the Furrion and also do you have the side marker cameras for the sides. Thanks

asked by: Jeff P

1

Helpful Expert Reply:

Yes we do have replacement Furrion monitors that will work with the Furrion camera you have at the rear of your 2019 356QB Forest River Hemisphere like with the 7 inch part # FR47FR. Then to add side cameras you'd just need the kit part # FCE48TASL which comes with cameras for both sides of the RV.

expert reply by: Jameson C

1

Answer 1

Since you have a Dometic AC unit the best option to replace it from Advent would be the part #ACDOM135 which was designed for this exact situation and would allow you an easy install since the electronics would plug right in.

view full answer...

Answer 2

Assuming your Sprinter has the factory tow package with the 7-way at the rear bumper, in addition to the #RED24FR Redarc Tow-Pro Liberty Brake Controller, you'll also need the #3063-P wiring harness and the #331-TPH-017. The connector to install…

view full answer...

Answer 3

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 4

You have it right so far, the 4-way connector is just as you have stated. Remember that Yellow has a L in it so that is the left side brake/turn signal and green has a R in it so that is the right side brake/turn signal. The colors for wiring a 7-way…

view full answer...

Answer 5

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 6

I spoke to Dexter and they said there is a bit of a process for installing the spindle nut properly. 1. You will need to thread on the inner nut, rotate the hub, then tighten the nut to 100 foot pounds. 2. Loosen the nut to remove the torque, making…

view full answer...

Answer 7

You said you checked the brake magnets. When inspecting them did you notice if the windings inside the magnets are showing? If so this is most likely the reason that the short is showing up on the controller when the vehicle is moving. This would…

view full answer...

Answer 8

The P-15 model information you provided for your Dexter axle does indicate its model, but you will still need to note its length and capacity before locating the correct replacement. If you are able to find a longer serial number somewhere on the…

view full answer...

Answer 9

It sounds like the left side may have a bad ground in the system or a loose ground. I would check over the complete wiring system and make sure all grounds have a good metal contact and no rust. Also check the wires to make sure the protective…

view full answer...

Answer 10

The Replacement Trailer Brake Magnet for Dexter Electric Brake Assemblies part #BP01-225 is designed for a 7,000 lb trailer axle.

view full answer...

Answer 11

Dexter recommends that you check the wires of the brake assemblies of your trailer to determine which magnet would be what you would need. If the wires are white you would need part #BP01-265 and if they are yellow part #BP01-301. However, aside from…

view full answer...

Answer 12

I spoke with my rep at Dexter axle and was informed your axle has a 3,500 lbs weight capacity, with a 58" spring center, and a 72" hub face. A comparable replacement is the Dexter Trailer Idler Axle Beam with EZ-Lube Spindles - 72"…

view full answer...

Availability of Replacement Furrion Monitor and Side Cameras

Products Referenced in This Question

Continue Researching