How to Add a 7-Way Connector to a 2012 Jeep Liberty
Question:
Good evening, I’m reaching out for information on how to wire a seven flat onto my Jeep liberty. It does not have any factory wiring. I have installed the product you have for the four pin. It is the kit that uses T connectors on the tail lights with a relay running from the battery to the back. I recently picked up a pop-up camper and I’m looking to have power using the seven way switch. Any information you can provide would be greatly appreciated.
asked by: Brandon P
Expert Reply:
Since your 2012 Jeep Liberty has a 4-flat connector you will need the Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires item # ETBC7. The kit includes a pre-wired 7- and 4-way trailer connector that mounts easily at the rear of your vehicle with an included bracket.
This kit is designed for use on a vehicle with an existing 4-way flat trailer connector and plugs directly into it. You will then connect the blue wire to the blue wire on the brake controller, connect the black wire to the positive post on your Jeep's battery. The white wire is your ground and you will need to securely attach it to a rust and paint free source of metal. The yellow wire will connect to your Jeep's reverse circuit.
This kit will provide you with the ability to control your trailer's brakes and also provide you with a 12v power wire for you trailer's accessory. I have linked an installation video below that will help you see the steps I have explained.
If your pop-up camper has brakes you will need a brake controller to operate them. I recommend the Tekonsha Prodigy P3 item # 90195.
Products Referenced in This Question
Tekonsha Prodigy P3 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Trailer Brake Controller
- Proportional Controller
- Electric
- Electric over Hydraulic
- Automatic Leveling
- Under-Dash Box
- Dash Mount
- Up to 4 Axles
- LCD Display
- Up to 360 Degrees
- Tekonsha
more information >
Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Accessories and Parts
- Trailer Brake Controller
- Installation Kits
- etrailer
more information >
Product Page this Question was Asked From
Tekonsha Prodigy P3 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Trailer Brake Controller
- Proportional Controller
- Electric
- Electric over Hydraulic
- Automatic Leveling
- Under-Dash Box
- Dash Mount
- Up to 4 Axles
- LCD Display
- Up to 360 Degrees
- Tekonsha
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: Brake Controller Installation: Starting from Scratch
- Article: Trailer Wiring Diagrams
- Article: Towing a Trailer? Let's Talk About Brake Controllers
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Article: Installing an Electric Brake Controller on 2007-2013 GM Full-Size Truck or 2007-Present GM SUV
- Article: How to Measure for Trailer Hitch Drop
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Q&A: Does the Tekonsha P3 Trailer Brake Controller Turn Off or Stay On All the Time
- Q&A: Parts Needed To Install A Brake Controller On A 2023 Freightliner Cascadia
- Q&A: Suspension Enhancement Recommendation for 2019 Toyota RAV4
- Q&A: Parts Needed to Add 7-Way & Brake Controller on 2023 Kia Sportage
- Q&A: My Vehicle has a 4-Pin Trailer Plug, but Trailer has 7-Pin Trailer Plug
- Q&A: Comparison of Tekonsha Prodigy P3 and Primus IQ Brake Controllers