Replacement Disc Brake Kit For Tie Down Engineering 46845 Disc Brake Hub
Question:
I have an older TDE axle with straight shaft spindles...hub # is 46845HECA. both bearings Im told are 1 3/8inch ID. do you have a hub and rotor combo that is compatable? Thanks
asked by: Tyson D
Expert Reply:
I can recommend the Kodiak Disc Brake Kit # K2HR35DKG to give you a new disc brake setup. Your Tie Down Hub 46845 is only a 9.6" diameter rotor and the 10" is the current size available. Your hub uses a Inner Bearing # L68149, Outer Bearing # L44649 and Grease Seal # 168255TB.
The Kodiak Disc Brake Kit # K2HR35DKG will require 2 of the Inner Bearings # L68149, Outer Bearings # L44649 and Grease Seals # 168255TB to mount on your TDE axle. You will also need the Standard Grease Caps # RG04-020, EZ Lube Grease Caps # RG04-040 or the Bearing Buddy Bearing Protectors # BB1980A-SS
![Bud M](https://images.etrailer.com/static/images/catg/people/2449_tn.jpg)
Products Referenced in This Question
Double Lip Seal for 3,700-lb Marine Hubs
- Trailer Bearings Races Seals Caps
- Seals
- Grease Seals - Double Lip
- 1.687 Inch I.D.
- 2.561 Inch O.D.
- Dexter
more information >
Bearing Buddy Bearing Protectors - Model 1980A-SS w/ Auto Check - Stainless Steel (Pair)
- Trailer Bearings Races Seals Caps
- Caps
- Bearing Protector Grease Cap
- 1.98 Inch
- Bearing Buddy
more information >
Replacement Trailer Hub Bearing - L44649
- Trailer Bearings Races Seals Caps
- Bearings
- Standard Bearings
- 1.063 Inch I.D.
- Bearing L44649
- Race L44610
- 3500 lbs Axle
- etrailer
more information >
Replacement Trailer Hub Bearing - L68149
- Trailer Bearings Races Seals Caps
- Bearings
- Standard Bearings
- 1.378 Inch I.D.
- Bearing L68149
- Race L68111
- 3500 lbs Axle
- etrailer
more information >
Grease Cap, 1.988" OD Drive In - Qty 2
- Trailer Bearings Races Seals Caps
- Caps
- Standard Grease Cap
- 1.98 Inch O.D.
- TruRyde
more information >
Grease Cap, 1.99" OD EZ Lube Drive in with Plug - Qty 2
- Trailer Bearings Races Seals Caps
- Caps
- E-Z Lube Grease Cap
- 1.99 Inch O.D.
- TruRyde
more information >
Product Page this Question was Asked From
Kodiak Disc Brake Kit - 10" Hub/Rotor - 5 on 4-1/2 - Dacromet and KodaGuard - 3,500 lbs
- Accessories and Parts
- Trailer Brakes
- Disc Brakes
- LH
- RH
- 3500 lbs
- Brake Assembly
- 5 on 4-1/2
- Hub and Rotor Assembly
- Kodiak
more information >
Continue Researching
- Article: Breakaway Kit Installation for Single and Dual Brake Axle Trailers
- Article: Trailer Drum Brakes vs. Disc Brakes: Making the Decision
- Q&A: Recommended Disc Brake System for Salt Water Boat Trailer with Tandem Axles
- Q&A: How to Connect a Surge Brake Actuator to Activate the Reverse Lockout Function
- Q&A: When Do Brakes Need to be Added to Both Axles of Tandem Axle Trailer
- Q&A: Should Trailer Wiring 5-Way Allow Trailer with Surge Brakes to Back Up When in Reverse
- Q&A: Converting Boat Trailer to Hydraulic Disc Brakes to Use In Saltwater
- Article: Most Popular Wheel Bearings
- Q&A: Disc Brake Actuator with Electric Lockout for Magic Tilt Trailer
- Q&A: How to Bleed Brakes on a Trailer with an Electric Over Hydraulic Actuator
- Article: 5 Tell-Tale Signs It’s Time to Replace Your Trailer’s Leaf Springs
- Article: How to Charge a Dump Trailer Battery
- Article: How to Bleed Your Trailer Surge Brakes
- Article: Brake Controller Installation on a Ford Full-Size Van