Installation of SnapPad XTRA Jack Pads for Lippert Leveling Systems

Question

Question:

I understand these will fit my Lippert stabilization feet 6. However the installation has you placing them under the feet and lowering the arms till the feet pop into the pads. Lippert stabilization arms have an auto cutoff when they are met with force. Will the pads pop on before the stabilizers cut out?

asked by: Murray

0

Expert Reply:

Yes, the SnapPad XTRA Jack Pads for Lippert Leveling Systems, # SN99FR do not require a tremendous amount of force to be seated. You will be okay. Happy Camping!

expert reply by: Michael R

0

Answer 1

All you're going to need to do is take note of the shape, the amount of jacks you have and measure the size of your jack feet. For instance, if you had 4 6" square feet then you could use the SnapPad XTRA Square 6 Jack Pads for…

view full answer...

Answer 2

I checked with the manufacturer, SnapPad, and verified the XTRA pads you asked about do fit 5-3/4" jack feet; so you can use the following: - SnapPad XTRA Jack Pads for Lippert Leveling Systems w/ 6" Square Jack Feet #SN99FR The…

view full answer...

Answer 3

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two…

view full answer...

Answer 4

Hey Joe, yes the Lippert stabilizer jack part #LC298707 does fit your Grand Design Transcend 245RL but it is sold individually so if you wanted a set for the front and the rear you would need to order a quantity of two.

view full answer...

Answer 5

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

I can definitely help set you up with everything you need to flat tow your 2023 Ford Expedition. Take a look at the list of parts below. I will start with the base plate and go from there. Base Plate - etrailer Invisible Base Plate Kit #e86YR Tow Bar…

view full answer...

Answer 8

I went out to our warehouse and test fit some SnapPads on the feet of the Lippert High-Speed Power Stabilizer Jack #LC298707 and found that the 6" square SnapPads were a fit. If your 2022 Forest River Vibe travel trailer only has one #LC298707…

view full answer...

Answer 9

Hey Dan, The ground for the Roadmaster Brake-Lite Relay Kit for Towed Vehicles #RM-88400 typically gets tied into the ground for the braking system to intertwine them so that they're active at the same time. When used to prevent turn signals from…

view full answer...

Answer 10

If you have 10" octagonal or concave round jack feet on your Baystar, then the SnapPad EQ Octagon Jack Pads for Equalizer Leveling System w 10" Octagon Jack Feet #SN76FR will work great. If not, you're going to have to measure your jack…

view full answer...

Answer 11

Kenny, those bolts for the B&W Companion 5th Wheel Trailer Hitch #BWRVK3500-5W should be torqued to 40 ft. lbs. Also, the pivot arms would need to be torqued to 80 ft. lbs, the draw down bolt should be tighten to 60 ft.lbs and the arms should be…

view full answer...

Answer 12

Hey Brad, thanks a bunch for going ahead and getting all those measurements in advance. Based on the measurements you've given, the TorkLift GlowStep Revolution Uprising Steps w/ Booster Step #TL52SR will work perfect for your coach. These steps…

view full answer...

Installation of SnapPad XTRA Jack Pads for Lippert Leveling Systems

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching