How Wide is the Powered Head on the Bulldog Powered Drive Trailer Jack

Question

Question:

What is the width of the power head? I want to mount sideways and be sure that I can open the tailgate on my truck with the trailer attached.

asked by: Michael C

0

Expert Reply:

I was able to go out to the warehouse and measure the width of the head on the Bulldog Powered Drive Trailer Jack # BD500199. The head is approximately 4-1/2" wide at its widest point.

expert reply by: Scott S

0

Bulldog Powered Drive Trailer Jack Head Width
(click to enlarge)

Answer 1

We don't have specific information on fits of parts like trailer jacks on individual coaches, but the Bulldog Powered Drive Trailer Jack - Drop Leg - A-Frame - 22" Lift - 4,000 lbs #BD500199 can be used on your 1985 Airstream and should fit…

view full answer...

Answer 2

There is no reason why you could not turn the jack at a 90 degree angle to gain more clearance. Due to the configuration of the holes in the mounting flange, you might need to drill new holes in your trailer tongue to mount the jack in that…

view full answer...

Answer 3

Your picture didn't make it through and I am not sure what product you are interested in.

view full answer...

Answer 4

In order to clear the leader hose and regulator mounting bracket on your 20 lb propane tank with the Camco RV Polyethylene Propane Tank Cover part #CAM40565 you would more than likely need to rotate the tank so that the backet and leader hose are…

view full answer...

Answer 5

Usually when this occurs, it's because the jack has been over extended; there is a small lock nut in the channel on the inner tube of this jack that if it's over extended will cut into the V channel on the inside. When this happens, it…

view full answer...

Answer 6

The replacement level for your Bulldog Powered Drive Trailer Jack #BD500199 is found as part #BD500193 on our site. It does come with the screws as well.

view full answer...

Answer 7

Yes we've confirmed with both Valterra and LaSalle Bristol that the threads of both of the extension rods are the same 1/4 inch size. So the #34466SP1112 that you referenced which is 12 inches long would work well for you.

view full answer...

Answer 8

The first step in troubleshooting an electric trailer jack like your Lippert Electric Trailer Jack with Footplate #LC285318 is to use the manual override instead of the power to see if the issue is mechanical or with power. If you're able to get…

view full answer...

Answer 9

When wiring up the Bulldog A-frame trailer jack #BD500187 you can use 12 gauge wire such as #12-1-1 (sold by the foot) as long as the distance from the jack to the battery is less than 20 feet. I am assuming that the battery is located at the front…

view full answer...

Answer 10

I went out to our warehouse to assist with the dimensions of the Bulldog Powered Drive Trailer Jack - Drop Leg - A-Frame - 14" Lift - 4,000 lbs - Black #BD500199. From the top of the mounting plate to the bottom of the motor housing is 12-7/8…

view full answer...

Answer 11

I have attached for you a list of the replacement parts that are available for the Bulldog Powered Drive Trailer Jack part #BD500199. I am not sure which part in particular that you are referring to but if it is not listed below then you would…

view full answer...

Answer 12

The Bulldog A-frame trailer jack #BD500199 is an excellent choice. I don't see any reason why you would have to rotate it 90 degrees for installation so no worries there. The easiest way to get more clearance between the tow vehicle and trailer…

view full answer...

How Wide is the Powered Head on the Bulldog Powered Drive Trailer Jack

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching