Can Air Lift Suspension Kit # AL57295 be Used on Lifted Truck

Question

Question:

Is the airlift suspension comparable With a lifted truck that is not factory height?

asked by: Robert

0

Expert Reply:

You can use Air Lift suspension kits like the part # AL57295 on vehicles that have lift kits but you have to also install a spacer to take up the additional space created by the lift kit. For example, we have the 2 inch spacer kit # AL52420, the 4 inch spacer kit # AL52440, and the 6 inch spacer # AL52460.

expert reply by: Jameson C

0

Answer 1

The Air Lift LoadLifter 5000 Air Helper Springs #AL57295 referenced in your question are confirmed to fit your 2016 Ram 3500 as long as the truck has rear leaf springs. With the truck jacked up, make sure you are first unbolting and removing the…

view full answer...

Answer 2

I have another option for you but you are correct, the Air Lift LoadLifter 5000 Air Helper Springs - Rear Axle #AL57295 you were looking at is only confirmed to fit the the 2003-2013 Ram 2500 and select 2003-2018 Ram 3500's and will not fit your…

view full answer...

Answer 3

If you are having an issue bottoming out, I recommend the Air Lift LoadLifter 5000 part #AL57295. It's specifically designed for 3/4-ton and 1-ton pickup trucks, motor homes, and commercial trucks and will provide your Dodge Ram with up to 5,000…

view full answer...

Answer 4

The Dexter Axle Torflex axles are basically broken up into the following categories: #9 - 1,000 - 2,200 lb #10 - 2,300 - 4,000 lb #11 - 4,100 - 6,000 lb #12 - 5,500 - 7,200 lb Based off of your 2004 R-Vision Trail-Lite Model 8306S being a tandem axle…

view full answer...

Answer 5

I sent your axle info to Dexter and they were able to determine that you have a set of 7k Dexter Torflex axles so the correct lift you need is the part #K71-725-02 which will give you a lift of 3-1/8 inches.

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

It sounds like the purpose of getting the air helper spring would be to counteract the 1 inch compression you're getting in your rear suspension caused by the pin weight of your 5th wheel. If that's the case, I believe that the AirLift 5000…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Can Air Lift Suspension Kit # AL57295 be Used on Lifted Truck

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching