Choosing Spring Return Or Non-Spring Return and Handle Recommendation For Bulldog Square Jack
Question:
Hi, 1 What Sidewind crank is recommended for the 25000 Lbs BD 182701 jack ? Part # please. 2 What model is more reliable with spring return or non spring return ? Thank you
asked by: Marius
Expert Reply:
The Replacement Bulldog Sidewind Jack Crank Assembly # BD015181 is recommended for the Bulldog Square Jack - Drop Leg w/ Spring Return # BD182701.
Both jacks are very reliable and rebuildable if you should have issues with the jacks. I do prefer the Bulldog Square Jack - Drop Leg w/ Spring Return # BD182701 over the Bulldog Square Jack - Drop Leg w/ Non-Spring Return # BD182700 as it is much easier to push down on the spring return jack when dropping the trailer than it is to bend down and lift the jack leg and lock in place when attaching the trailer. And if the spring should break they are also replaceable with the Replacement Return Spring # TJD-12000-RSP.
Products Referenced in This Question
Replacement Sidewind Handle for Bulldog Heavy-Duty Trailer Jacks - 13-1/2" Radius - Black
- Accessories and Parts
- Camper Jacks
- Trailer Jack
- Handles and Cranks
- Sidewind
- Bulldog
more information >
Bulldog Square Jack - Drop Leg w/ Non-Spring Return - Sidewind - 26" Lift - 12,500 lbs
- Trailer Jack
- Car Hauler
- Enclosed Trailer
- Fifth Wheel Trailer
- Gooseneck Trailer
- Utility Trailer
- Leveling Jacks
- Tongue Jacks
- Steel
- 10001 lbs or More
- Sidewind Jack
- 26 Inch Lift
- Weld-On
- With Rectangle Foot
- Bulldog
more information >
Replacement Return Spring for etrailer and Ram Square, Direct Weld Jacks - 10,000 lbs
- Accessories and Parts
- Camper Jacks
- Trailer Jack
- Hardware
- Springs
- etrailer
more information >
Product Page this Question was Asked From
Bulldog Square Jack - Drop Leg w/ Spring Return - Sidewind - 26" Lift - 12,500 lbs
- Trailer Jack
- Car Hauler
- Enclosed Trailer
- Fifth Wheel Trailer
- Gooseneck Trailer
- Utility Trailer
- Leveling Jacks
- Tongue Jacks
- Steel
- 10001 lbs or More
- Sidewind Jack
- 26 Inch Lift
- Weld-On
- With Rectangle Foot
- Bulldog
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Video: Rebuilding of an etrailer or Ram Square Jack
- Shop: Replacement Return Spring for etrailer and Ram Square, Direct Weld Jacks - 10,000 lbs
- Video: Review of etrailer Replacement Return Spring etrailer Ram Square Direct Weld Jack - TJD-12000-RSP
- Search Results: 9/16 wheel studs
- Search Results: 9/16 lug nut
- Q&A: Determining The Correct Replacement Drop Leg Return Spring For 10,000lb Side Wind Trailer Jack
- Search Results: lug nut
- Q&A: Replacement Wheel Stud For Dexter Hub & Drum 8-219-13UC3
- Q&A: Replacing the Drop Leg Spring Loaded Pull Pin on a Bulldog 180 Series Square Jack
- Shop: Bearing Kit, 14125A/ 25580 Bearings, 10-36 Seal
- Shop: Drive-in Wheel Bolt for Trailer Wheel Hubs - 9/16" Diameter x 2-5/16" Long - Qty 1
- Shop: CE Smith Trailer Wheel Lug Nut - Zinc-Plated Steel - 1/2" - Qty 1
- Shop: Trailer Wheel Lug Nut - 9/16" Diameter - Zinc Plated
- Shop: Trailer Hub Wheel Stud, Drive-In, 9/16" x 2" - Qty 1
- Shop: Dexter Trailer Hub & Drum for 5,200- to 7,000-lb Axles - 8 on 6-1/2 - 9/16" Studs - Pre-Greased
- Search Results: equalizer
- Q&A: Dimensions of the Replacement Return Spring Part # TJD-12000-RSP
- Q&A: Amperage of Brake Magnets and Size of Wire Used To Connect 7-Way Trailer Plug To Electric Brakes
- Search Results: jack pin
- Search Results: odometer
- Search Results: morryde shackle
- Q&A: Diagram of a 10k Bulldog Landing Gear Jack for Gear Replacement
- Q&A: Determining Replacement Return Spring For Jack On PJ Trailer Measuring 12"x3/4" Diameter