Timbren Axle-Less Trailer Suspension System w/ Electric Brake Hubs to Replace 2800 lbs Dexter Axle

Question

Question:

I have a Dexter axle 2800lbs and the electric brakes and axle are one piece. I need to replace one. Do they make them still. The measurement for the center of the leaf springs are 66 inches and havent been able to find them. Any help would be appreciated

asked by: Thomas O

0

Expert Reply:

Thanks for the pictures, they were very helpful. I have a great solution for you but no, they do not make one piece axle and brake assemblies that will fit your spring spacing. I recommend the Timbren Axle-Less Trailer Suspension System w Electric Brake Hubs item # A35RD545E. The individual suspension units replace your existing axle and operate independently. The 4" drop spindle should match up with your existing axle and provide the same ride height. They will fit any frame width and are rated up to 3,500 lbs. This will make replacing your older axle a lot easier and more cost effect.

expert reply by: Jerred H

0

customer pic
(click to enlarge)

customer pic 2
(click to enlarge)

Answer 1

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 4

There really isn't a particular maximum trailer weight that is used to determine when brakes need to be added to both axles of a tandem axle setup. While I do still recommend checking your local laws, I am also not aware of any general laws that…

view full answer...

Answer 5

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 6

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...

Answer 7

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 8

The Dexter Nev-R-Adjust electric trailer brakes can be manually adjusted. There are a couple teeth of the adjustment wheel that are exposed just under the lever that you referenced. I have attached a photo showing the teeth. You will likely need a…

view full answer...

Answer 9

You will need to do some measuring to determine if the 10 Inch Electric Brake Assembly LH, item #AKEBRK-35L, is the correct assembly for your trailer. Measure the diameter of the mounted brake shoe, the width of the lining and the distance between…

view full answer...

Answer 10

On Dexter 12" Nev-R-Adjust Electric Brake Assembly #23-458 the shoe pad thickness is 3/16 of an inch. Dexter says that you should replace the shoes if the material gets down to 1/16 of an inch thick or less.

view full answer...

Timbren Axle-Less Trailer Suspension System w/ Electric Brake Hubs to Replace 2800 lbs Dexter Axle

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching