Side Cameras that Can be Used with Rear View Safety Universal Mirror Monitor

Question

Question:

I am needing a part for this camera for the side camera

asked by: Perry

0

Expert Reply:

For side cameras that can be used with the RVS monitor part # RVS-619N you'd want the part # RVS-775L for the driver's side and part # RVS-775R for the right hand side.

expert reply by: Jameson C

0

Answer 1

If you are looking to replace the camera so that it works with your monitor #RVS-6139N that you referenced, it looks like your current camera resembles part #RVS-775R. Since you are having trouble getting a camera feed on your monitor and it looks…

view full answer...

Answer 2

The Rear View Safety Windshield Mounting Arm #RVS-619UM is capable of supporting a monitor that is up to 3lbs and can mount with the windshield style mirror mounting bracket. It was designed for use with their Rear View Safety Universal Mirror…

view full answer...

Answer 3

I have the perfect solution for you! To add a multiplexer to your Rear View Safety #RVS-619N-S system you can use the Rear View Safety Multiplexer Box #RVS-501N , which is the part that is normally included in the upgraded #RVS-770619N-S system.…

view full answer...

Answer 4

I'll be happy to help you with your questions but first, the part #RVS-910 you asked about will only fit a 2003-2016 Chevy Express. Since you have a 2019 you need the part #RVS-913 instead. This does come with 10 meters of cable and while we…

view full answer...

Answer 5

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 6

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 7

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 8

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 9

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 10

A 4-way trailer connector will have four functions which means it will also have four wires for the exception of wishbone harnesses. These four functions are ground, tail light, right turn, and left turn. The ground function will usually be…

view full answer...

Answer 11

It really just depends on what the wires are for. Most likely you have several ground wires among the 8 as well as a couple running light circuits in there as well. You just have to run all of the wires to the correct circuits. The 4-way wiring of…

view full answer...

Answer 12

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Side Cameras that Can be Used with Rear View Safety Universal Mirror Monitor

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching