Recommended Method For Installing Longer 7-way Trailer Connector Harness On Trailer W/ 9' Deck
Question:
I have a 2018 Rockwood A-frame camper .. I am adding a 9 foot deck on the front .. it currently has a 7 pin harness/plug on the trailer now .. in your opinion what would the best way to add to the existing wiring .. thanks
asked by: G
Expert Reply:
The best way would be replacing the current 7-way connector at the junction box and installing a longer harness.
The junction box should be located not too far behind the coupler of your 2018 Rockwood A-Frame camper and will be on the inside of the A-frame.
I recommend going with the 7-Way Molded Connector w/ 18' Cable - Trailer End # 50-67-106 which will be plenty long to clear the 9' deck on your trailer and it can be cut down to the exact length you want/need. Just make sure to not make it too short that when you turn it gets pulled on.
You will need to use 7 of the ring terminals # 44-5310A to be able to install the harness in your junction box.
The reason I like this method instead of an adapter harness such as the # 50-67-210 or # TLW6510 is that there is only one connection point where the connector plugs in to the 7-way connector on your tow vehicle. On the adapter harness you have two connection points which is just adding additional locations to possibly have problems.
I included a video of the # 50-67-106 being installed for you to take a look at.
Products Referenced in This Question
Ring Terminal - 12-10 Gauge Wire - 3/16" Ring ID
- Wiring
- Wire Connectors
- Ring Terminals
- 3/16 Inch Diameter
- 12-10 Gauge
- Flint Hill Goods
more information >
7-Way Molded Connector w/ 18' Cable - Trailer End
- Trailer Wiring
- Trailer Connectors
- Trailer End Connector
- 11 - 20 Feet Long
- Plug and Lead
- 7 Round - Blade
- Bargman
more information >
TorkLift Wiring Harness Extension - 7-Way RV - 10' Long
- Trailer Wiring
- Wiring Adapters
- Single-Function Adapter
- 6 - 10 Feet Long
- 7 Round - Blade
- Plug and Lead
- 7 Round - Blade
- TorkLift
more information >
Product Page this Question was Asked From
Bargman 7-Way Molded Trailer Wire Connector - Double-Ended - 8' Long
- Trailer Wiring
- Trailer Connectors
- Trailer End Connector
- 6 - 10 Feet Long
- Plug and Lead
- 7 Round - Blade
- Bargman
more information >
Continue Researching
- Q&A: 7-Way Trailer Plug Adapter or Compatibility with Lance Slide-In Truck Bed Camper
- Article: Trailer Wiring Diagrams
- Article: How to Mount a Truck Bed Camper
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Q&A: 7-Way RV to 7-Way Dinghy Tow Bar Wiring Extension
- Q&A: Will The AM31990 Tire/Wheel Fit On The etrailer Hitch Mounted Spare Tire Carrier e98ZR
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: Differences Between Demco eZ-Latch Trailer Couplers
- Q&A: Replacement Parts for Lippert RV Steps 171317
- Q&A: Is There a Weight Capacity for TorkLift Locking FastGun Turnbuckles
- Q&A: No Brake Lights With Ignition Off Using Roadmaster Brake-Lite Relay Kit On a 2010 Honda Fit
- Article: 4-Step Guide to Installing RV Solar Power
- Article: Stability Control for Heavy Duty Vehicles
- Article: Wiring Trailer Lights with a 5-Way Plug (It's Easier Than You Think)