Is There a Way to get a 14 Inch Bolster Bracket?

Question

Question:

Is there a 14inch version of this bracket?

asked by: Dave T

1

Helpful Expert Reply:

We do have an option to get you to the 14 inches, but it will be parts that need to be purchased separately. So with that being said, the CE Smith Bolster Bracket # CE10102G will measure 12 inches tall and if paired with the CE Smith Swivel Bracket # CE10200G, it will get you to the 14 inches.

expert reply by: Lazer S

1

Answer 1

The CE Smith Galvanized Bolster and Swivel Mounting Brackets for Bunk Boards #CE10001G-4 come with nuts and bolts to attach the swivel brackets to the bolster brackets, but you will need to supply either lag bolts or other through bolt hardware to…

view full answer...

Answer 2

We have had this come up before and the manufacturer stated that the CE Smith Roller Bunks for Boat Trailers #CE27710 would work for a 15' boat in place of your 7' bunk boards as long as the cross members are 56 inches or less. Which your…

view full answer...

Answer 3

The CE Smith Brackets #CE10196G-4 you mentioned do not have a stated weight capacity but as long as you install them properly and use your best judgement with placement and with the bunks you'll be fine with what you are doing. Here's…

view full answer...

Answer 4

The CE Smith Roller Bunks, #CE27700, that you referenced would be a great option for your boat trailer. These roller bunks are 4 ft long and they can be mounted directly on top of your current wood bunks. You can also use the CE Smith Mounting…

view full answer...

Answer 5

Since your main concern is the marks on the hull of your boat I recommend going to the Yates TPR Ribbed Wobble Roller. These rollers are constructed of thermal-plasticized rubber which is a non-marking, non-scratching material. It is stronger and…

view full answer...

Answer 6

I spoke with my contact at CE Smith, and they said the Bolster and Swivel Bracket Assembly for Boat Trailers, like part #CE10000G, do not bear the weight of the boat. The U-bolt that attaches the brackets to the trailer frame support the weight of…

view full answer...

Answer 7

I spoke to my contact at CE Smith and they informed me that the CE Smith Light Duty Vertical Bunk Bracket part #CE10600G does not have a weight capacity. However, so long as you use multiple for each board you should not have any issues with your…

view full answer...

Answer 8

Thank for the photos of your boat trailer! The CE Smith Double U-Bolt Bolster and Swivel Bracket Assemblies #CE10196G-4 that you referenced are a great option to replace the existing bunk system on your boat trailer. These bolster brackets and swivel…

view full answer...

Answer 9

Given the dimensions you provided, I believe that a u-bolt kit such as #CE23103 that's typically used to mount a 2 inch square trailer axle to the leaf spring pack would be your best bet. The kit includes two assemblies, each of which includes…

view full answer...

Answer 10

The U-bolts we offer with designed to fit a 2-1/8 inch frame are part #CE15501A. We do not offer any other U-bolts designed to fit a frame that size. I pulled one of the part #CE15501A U-bolts from our warehouse and took some measurements for you. I…

view full answer...

Answer 11

If your Dutton Lainson roller bunks have a flat bottom surface like part #DL21741 then you can mount them directly to the CE Smith Bolster and Swivel Bracket Assemblies #CE10196G-4 as shown in the linked photo. These are the tallest ones we offer. If…

view full answer...

Answer 12

Yes the Draw Tite trailer hitch part #DT82QR that you referenced does fit your 2021 Toyota RAV4 XLE as we have confirmed this with Draw Tite. I attached an install video for this on a similar 2023 Toyota RAV4 for you to check out as well.

view full answer...

Is There a Way to get a 14 Inch Bolster Bracket?

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching