Availability Of Ball Mount That Is Straight And Has A Single 1-7/8 Hitch Ball
Question:
Do you have a trailer hitch with the following properties: - 2inch tubular shank - 5/8inch hitch pin hole - 1-7/8inch fixed ball mount - 8inch length between pin hole and ball center 12inch overall. - 0 - 0 rise Similar to item #3371802207
asked by: Keith I
Expert Reply:
It sounds like you are looking for something similar to the Buyers Products Tri-Ball Hitch - Tubular Shank with Chrome Balls # 3371802207 that only has a 1-7/8" diameter hitch ball.
The closest option we have to this is the etrailer Ball Mount Kit # 989891 which includes a ball mount that measure 8-1/2" from the center of the hitch pin hole to the center of the hitch ball hole, and is right around 12" long overall. Now this ball mount does not have 0" rise/drop, but has a 3/4" rise which would work perfectly. With the tongue weight of the trailer on the hitch, this will be pretty close to level.
This kit includes a standard hitch pin and clip, but I recommend upgrading to the etrailer Trailer Hitch Receiver Lock for 2" Hitches - Flush - 2-5/8" Span - Chrome # e98880 which will allow you to lock your ball mount to your vehicles trailer hitch receiver.
I included videos of the products mentioned for you to take a look at.
Products Referenced in This Question
etrailer Ball Mount Kit for 2" Hitches - 3/4" Rise or 2" Drop - 7,500 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- 1-7/8 Inch Ball
- 2 Inch Ball
- Two Balls
- Steel Ball
- Steel Shank - Gloss Black
- Drop - 2 Inch
- Rise - 1 Inch
- Fits 2 Inch Hitch
- 7500 lbs GTW
- Class III
- Ball Mount Kit
- etrailer
more information >
etrailer Trailer Hitch Receiver Lock for 2" Hitches - Flush - 2-5/8" Span - Chrome
- Trailer Hitch Lock
- Standard Pin Lock
- Keyed Alike
- Chrome
- Fits 2 Inch Hitch
- Flush Pin
- 2-5/8 Inch Span
- etrailer
more information >
Product Page this Question was Asked From
Buyers Products Tri-Ball Hitch - Tubular Shank with Chrome Balls
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- 1-7/8 Inch Ball
- 2 Inch Ball
- 2-5/16 Inch Ball
- Three Balls
- Steel Ball
- Steel Shank - Gloss Black
- Drop - 0 Inch
- Rise - 0 Inch
- Fits 2 Inch Hitch
- 10000 lbs GTW
- Class IV
- Buyers Products
more information >
Continue Researching
- Article: How to Measure for Trailer Hitch Drop
- Article: My Trailer Hitch Doesn't Fit
- Q&A: Recommended Kayak Carrier for 2 Inch Round Bar Roof Rack
- Article: Brake Controller Installation on a Ford Full-Size Van
- Q&A: How to Test Old Trailer Wiring to Find Out What Each Wire/Circuit Does
- Q&A: Where is Cold Side of Brake Switch Normally Found
- Q&A: How Much Voltage Is On Cold Side Wire Of Vehicle Stop Light Switch?
- Q&A: Measuring Fit of Fastway ONEstep Wheel Chocks
- Article: How to Choose the Right Trailer Hitch Class
- Q&A: What is the Weight Capacity and Air Pressure Ratings on the 15 X 6 Inch Steel Wheel - 6 on 5-1/2
- Q&A: Trailer Tires Showing Excessive Wear on Inside Edges of Tread
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: Trailer Wiring Diagrams
- Article: Brake Controller Installation: Starting from Scratch