Determining Correct Hanger Spacing For Installing Single-Axle Hanger Kit APS4 W/ 24-7/8" Leaf Spring
Question:
Hi, Can you tell me the proper mounting dimension for your APS4 leaf spring hanger kit with SP-222275 leaf spring? I have researched online and found a few conflicting dimensions. Thanks
asked by: Matt
Expert Reply:
The 6-Leaf Double-Eye Spring for 5,300-lb Trailer Axles - 24-7/8" Long # SP-222275 you were looking at measures 24-7/8" long where the springs mentioned for the Single-Axle Trailer Hanger Kit for Double-Eye Springs - 3-1/4" Front, 1-1/4" Rear # APS4 are all 25-1/4" long so the listed measurements will likely be a little too far apart for you.
With a 25-1/4" spring the spacing between the front and rear hangers center to center should be around 24-7/8", but since the spring you are wanting to use is 3/8" shorter you will need to reduce the spacing by 3/8" which will be around 24-1/2".
Now you will want to test fit these first and make sure you have the proper angle between the leaf spring and the rear hanger. This angle should not exceed 45 degrees.
Since trailer frames are all different it is important to verify the spring is set correctly before final welding, as minor adjustments to the spacing may be required.
Now the # APS4 does not include the U-bolt kits required to mount the axle to the springs so you will need # APUBR-8 assuming that you have a 3" diameter based on the weight rating of the spring you want.
I included videos of the products mentioned for you to take a look at.
Products Referenced in This Question
U-Bolt Kit for Mounting 5,200-lb to 7,000-lb, Round Trailer Axles - 7" Long U-Bolts
- Trailer Suspension Parts
- U-Bolt Kits
- Camper
- Car Hauler
- Utility Trailer
- 5200 lbs - 7000 lbs
- Round Axle - 3 Inch
- 1/2 Inch Diameter
- 7 Inch Long
- Dexter
more information >
6-Leaf Double-Eye Spring for 5,300-lb Trailer Axles - 24-7/8" Long
- Trailer Leaf Springs
- Double Eye Springs
- 5300 lbs
- 1-3/4 Inch Wide
- 6 Leaf
- 24-7/8 Inch Long
- Universal Group
more information >
Product Page this Question was Asked From
Single-Axle Trailer Hanger Kit for Double-Eye Springs - 3-1/4" Front, 1-1/4" Rear
- Trailer Suspension Parts
- Hangers
- Suspension Kits
- Boat Trailer
- Camper
- Car Hauler
- Snowmobile Trailer
- Utility Trailer
- Double Eye Springs
- Single Axle
- etrailer
more information >
Continue Researching
- Shop: Road Armor Shock Absorbing Equalizer Kit - Tandem Axle - Qty 2
- Shop: 6-Leaf Double-Eye Spring for 5,300-lb Trailer Axles - 24-7/8" Long
- Q&A: Installing Leaf Springs on Single Axle Trailer
- Q&A: Upgrading Dexter Double-Eye Spring 072-020-00
- Shop: 6-Leaf Double-Eye Spring for 5,300-lb Trailer Axles - 24-7/8" Long
- Shop: Single-Axle Trailer Hanger Kit for Double-Eye Springs - 3-1/4" Front, 1-1/4" Rear
- Shop: Rear Hanger with Bushing for Single Axle Trailer Suspensions with 1-3/4" Double Eye Springs
- Shop: 4-Leaf Double-Eye Spring for 5,000-lb Trailer Axles - 25-1/4" Long
- Shop: Trailer Axle with Idler Hubs - 5 on 4-1/2 Bolt Pattern - 89" Long - 3,500 lbs
- Q&A: Recommended 2014 Arctic Fox Travel Trailer Leaf Springs and Shocks
- Q&A: Hanger Placement with 3,500 lb Axle with Hanger Kit part # APS4 On Trailer with Axles Under Springs
- Q&A: Hanger Distance Recommendation for Trailer Leaf Spring that Measures 25-1/4 inches
- Q&A: How Far Apart Should Hangers be Mounted for 27 Inch Leaf Springs
- Q&A: Hanger Spacing Recommendation for Leaf Spring that is 25-1/4 inches Long
- Video: Universal Group Trailer Suspension - Leaf Spring Suspension - SP-222275 Review
- Video: Lippert Road Armor Shock Absorbing Equalizer Kit Installation - 2021 Grand Design Imagine Travel Tra
- Video: Lippert Road Armor Shock Absorbing Equalizer Kit Review
- Video: MaxxAir RV Vents and Fans - Roof Vent - MA00-07000K Review
- Article: Where to Position the Trailer Axle?
- Search Results: trfa916dlnz
- Search Results: 2000 lb axle
- Search Results: torflex axle
- Search Results: aps2
- Search Results: hangers
- Search Results: springs
- Search Results: trailer hangers