Replacement Driver Leg for Lippert Ground Control 2.0 System
Question:
Need information regarding options since the 241846 is not in stock. Can I use the 241845 instead?
asked by: Thane M
Expert Reply:
I have a solution for you and just as an FYI, Lippert had some difficulties with manufacturing and materials procurement during the pandemic; the Heavy Duty Driver Leg for Lippert Ground Control 2.0 Landing Gear # LC241846 was one of their parts that they had to stop producing briefly. They have recently (spring 2021) started production on these and expect them to be back in circulation at some point in the next couple of months.
With regards to your main question, the # LC241846 is 29-1/2" long where the # LC241845 is 33-1/2" long, so they're not cross compatible unless you were to swap both legs. However, I spoke with my contact over at Lippert and they mentioned that the Replacement Lead Leg for Venture 5th Wheel RV Landing Gear # LC119102 is the same as the # LC241846. The motor would connect to your old gear box and this leg and then you'd just need to swap your foot and pin over to make it work.
Until the # LC241846 is available again or replaced by a newer model, you can use the # LC119102 to replace your old leg.
Products Referenced in This Question
Replacement Lead Leg for Venture 5th Wheel RV Landing Gear
- Accessories and Parts
- Camper Jacks
- Trailer Jack
- Legs
- Driver Leg
- Lippert
more information >
Replacement Heavy-Duty Landing Gear Jack Leg for Ground Control 2.0 - Extended
- Accessories and Parts
- Camper Jacks
- Trailer Jack
- Legs
- Driver Leg
- Lippert
more information >
Product Page this Question was Asked From
Replacement Lead Leg for Venture 5th Wheel RV Landing Gear
- Accessories and Parts
- Camper Jacks
- Trailer Jack
- Legs
- Driver Leg
- Lippert
more information >
Continue Researching
- Shop: Replacement Lead Leg for Venture 5th Wheel RV Landing Gear
- Shop: Replacement Heavy Duty Driver Leg for Lippert Ground Control 2.0 Landing Gear
- Shop: Stromberg Carlson Electric Landing Gear Set - Weld On - 34-7/8" Lift - 6,500 lbs
- Shop: Replacement Heavy-Duty Landing Gear Jack Leg for Ground Control 2.0 - Extended
- Q&A: Is There a Replacement Bevel Gear Kit for Lippert Ground Control 2.0 Front Landing Gear
- Shop: Replacement Lead Leg for Stromberg Carlson Landing Gear - 33-1/2"
- Shop: Replacement Lead Leg for Venture 5th Wheel RV Landing Gear
- Shop: Replacement Lead Leg for Keystone Montana 5th Wheel Landing Gear
- Video: Bulldog Camper Jack - Landing Gear - BD500162 Review
- Q&A: Is There a Leg Repair Kit Available for a LC241845 Leg
- Search Results: 241846
- Video: Stromberg Carlson Landing Gear Replacement Lead Leg Review
- Q&A: Replacement Landing Gear for 2010 Open Range 5th-Wheel Trailer
- Q&A: Solution for Broken Fulton Landing Gear Box
- Q&A: Replacement Landing Gear for 2004 Carriage 5th Wheel Trailer
- Search Results: ma59fr
- Search Results: ventline replacement cover
- Search Results: fan
- Search Results: vent cover
- Search Results: ventline replacement lids
- Search Results: plumbing vent
- Q&A: Replacement Leg for Lippert Ground Control 2.0 LC241846
- Q&A: How to Remove Lower Bevel Gear on Venture Landing Gear
- Video: Review of Lippert Components Power Landing Gear Repair Kit - LC146060
- Video: Review of Lippert Components Trailer Jack - Camper Jack - LC241846
- Video: Review of Lippert Components - Trailer Jack,Camper Jack - LC146059
- Video: etrailer Landing Gear Set Review