What Is The Width Of The Curt Trailer Hitch Receiver 13359?

Question

Question:

I need to know the width of this item from bolt hole on the left to bolt hole on the right so I can be sure it will fit my frame width before ordering. Thanks

asked by: Donnie T

0

Expert Reply:

I had our warehouse measure the Curt Trailer Hitch Receiver # 13359 you were looking at and it measures 33-1/2" wide from the center of the left bolt hole to the center of the right bolt hole as shown in the included diagram.

I included a link to the written instructions of the # 13359 for you to take a look at.

expert reply by: Samuel C

0

Dimensions Of Curt Trailer Hitch Receiver # 13359
(click to enlarge)

Answer 1

Yes, the Curt Trailer Hitch Receiver #C14355 is a fit for your 1999 Ford F-150 Flareside.

view full answer...

Answer 2

The Curt Trailer Hitch Receiver #C14355 is going to be 35-1/2" wide. The more important measurement to look at is going to be the mounting bolt holes. I have included an image below with the mounting bolt hole spacing when measuring on center.

view full answer...

Answer 3

The only differences in the 3 Curt Trailer Hitch Receivers #13355, #C13038 and #13359 for your 1999 Ford F-150 XL Flairside, is the construction and shape of the receiver cross tube and mounting plates. Of these 3 I would choose the Receiver #C13038.…

view full answer...

Answer 4

It is true that the center of the rearmost bolt holes for the Curt Trailer Hitch Receiver #C14355 measure 32-11/16" on center, but since these bolt holes are oblong this trailer hitch will still fit your 1999 Ford F-250. If you note in the…

view full answer...

Answer 5

I spoke with my contact at CURT about Trailer Hitch #C14355. From side to side, the holes that would be furthest forward on the truck are 34 inches apart on center. The 2 sets that are at the end of the hitch are 33-11/16 inches apart on center.…

view full answer...

Answer 6

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 8

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 9

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 10

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 11

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 12

When installing/adjusting the Solera RV Slide-Out Awning #LCV000163285 tension is applied by rotating the awning roller 14 times. This should apply the needed spring tension so that the fabric doesn't billow in the wind or leave enough slack that…

view full answer...

What Is The Width Of The Curt Trailer Hitch Receiver 13359?

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching