Determining The Correct Replacement Hub For Hammerblow H-1000
Question:
Im looking for a replacement hub for a Hammerblow H-1000 5x4.5. Any help would be greatly appreciated. Thanks
asked by: Chris M
Expert Reply:
I would be happy to help you find the correct replacement hub for your Hammerblow H-1000, but you will need to determine which inner and outer bearings your spindle uses as I was unable to find any information on a specific replacement hub for you.
To determine which inner and outer bearing your spindle uses you will want to remove one of your current hubs and look for the bearing numbers stamped in the face of each bearing as shown in the included picture of the # L44649.
If your bearings are worn to the point that you cannot read the bearing numbers you will need to use digital calipers like # PTW80157 to precisely measure your spindle according to the included diagram.
If you can email me the bearing numbers or spindle measurements I would be happy to recommend a replacement hub for you.
Products Referenced in This Question
Replacement Trailer Hub Bearing - L44649
- Trailer Bearings Races Seals Caps
- Bearings
- Standard Bearings
- 1.063 Inch I.D.
- Bearing L44649
- Race L44610
- 3500 lbs Axle
- etrailer
more information >
Product Page this Question was Asked From
4" Carbon Fiber Digital Caliper
- Hand Tools
- Measuring and Layout Tools
- Digital Calipers
- Carbon Fiber
- Performance Tool
more information >
Continue Researching
- Shop: D Washer for EZ Lube Spindles
- Shop: Trailer Idler Hub Assembly for 2,000-lb Axles - 5 on 4-1/2 - Galvanized
- Shop: Trailer Idler Hub Assembly for 3,500-lb Axles - 5 on 4-1/2 - Galvanized
- Video: etrailer Trailer Idler Hub Assembly Installation
- Q&A: Replacement Hub for Hammer Blow Hub Part HB732 on Old Trailer
- Shop: DeeMaxx Trailer Idler Hub for 3,500-lb Axles - 5 on 4-1/2 - Galvanized
- Shop: CE Smith Trailer Idler Hub Assembly w/ Case for 2.5K Axles - 5 on 4-1/2 - Galvanized - Pre-Greased
- Shop: Hub Bearing Kit for Lippert, Dexter, and AL-KO Axles - 3,500 lb with #84 Spindle
- Shop: Easy Grease Trailer Idler Hub Assembly for 3.5K Axles - 5 on 4-1/2 - Galvanized
- Shop: Trailer Wiring
- Q&A: What Seals Will be the Correct Replacements for an H-1000 Hub?
- Q&A: Replacement Bearing Kit for Reliable Brand H-1000 Series Hub
- Q&A: Difference Between an Idler Hub and a Hub/Drum
- Video: Review of TruRyde Washer For 1 Inch Spindle - SW1000
- Video: etrailer Trailer Hubs and Drums - Hub - AKIHUB-545-2-G-EZ-1K Review
- Video: etrailer Trailer Hubs and Drums - Hub - AKIHUB-545-2-G-1K Review
- Video: CE Smith Trailer Hubs and Drums CE13215 Review
- Video: Review of TruRyde D Washer For EZ Lube Spindles - 5-23
- Search Results: 5x4.5 hub
- Search Results: leaf spring
- Q&A: Replacement Axle Recommendation For Small Popup Camper
- Q&A: Recommended Replacement Axle And Brakes For Popup Camper
- Video: Dexter Axle Trailer Axles - Leaf Spring Suspension - 20545I-EZ-72-10 Review
- Search Results: st145r12
- Search Results: axle
- Search Results: leaf spring hanger
- Search Results: weld on bracket
- Search Results: trailer axle
- Q&A: Extending the Charger Lead Wires on NOCO Genius Battery Charger
- Article: Where to Position the Trailer Axle?