Why Cant Gen-Y Glyder Shock Absorbing Ball Mount for 2 Hitches # 325-GH-12001 Flip Upside Down
Question:
Is there a way to get a 1 or 2 inch rise with the Gen-Y Glyder 2-in 3.5-in rise hitch? It seems this should be possible by simply inverting the whole hitch assembly not just the ball platform but will it support the load this way?
asked by: Phil B
Expert Reply:
To switch between the rise and drop position of the Gen-Y Glyder Shock Absorbing Ball Mount for 2" Hitches # 325-GH-12001 requires removing the ball platform, flipping it, and then reinstalling it to the bracket. The main shank assembly can't flip as it is angled up slightly due to it's spring setup. It would not function properly with the spring assembly inverted.
With just the platform inverted using the lower set of mounting bolts on the shank you'd get the lower 1-2 inch rise you are wanting.
Product Page this Question was Asked From
Gen-Y Glyder Shock Absorbing Ball Mount for 2" Hitches - 2" Drop - 7K
- Trailer Hitch Ball Mount
- Adjustable Ball Mount
- No Ball
- 1 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Drop - 2 Inch
- Rise - 0 Inch
- Fits 2 Inch Hitch
- 7000 lbs GTW
- Shock Absorbing
- Gen-Y Hitch
more information >
Continue Researching
- Shop: Gen-Y Glyder Shock Absorbing Ball Mount for 2" Hitches - 2" Drop - 7K
- Q&A: Using A Curt TruTrack Weight Distribution With Gen-Y Weight Distribution Shank
- Q&A: Can I Use a Ball Mount Upside Down to Create a Rise Instead of a Drop
- Shop: Powerbuilt Trim Pad Remover
- Shop: Suspension Enhancement
- Shop: Transmission Cooler
- Video: Timbren Vehicle Suspension TA25723-90AD00 Review
- Video: Timbren Rear Suspension Enhancement Installation - 2012 Toyota 4Runner
- Article: How to Install Tire Chains
- Q&A: Timbren Suspension Enhancement for a 2011 Toyota FJ-Cruiser Trail Edition
- Q&A: How to Prevent Sag While Towing with a Lifted 2013 Toyota FJ Cruiser
- Shop: Timbren 1/2" Spacer For Raised Frame Vehicles - 1/2" bushing
- Shop: Brake Controller
- Shop: Tire Chains
- Shop: Trailer Hitch
- Shop: Timbren 1/2" Spacer for Raised Frame Vehicles
- Shop: Spacer Kit for Timbren Suspension Enhancement System
- Shop: Timbren 1" Spacer For Raised Frame Vehicles - 1/2" Bushing
- Shop: Timbren 1" Spacer For Raised Frame Vehicles - 3/8" Bushing
- Q&A: How to Add Sway Control to a Weight Distribution System
- Q&A: Is There A Cushioned Gen-Y Ball Mount Compatible With A Weight Distribution System?
- Q&A: Comparing Gen-Y and Curt Shock Dampening Ball Mounts
- Search Results: curt rebellion xd
- Search Results: rockerball
- Video: Review of Curt Trailer Hitch Ball Mount - Adjustable Ball Mount - C83WR
- Video: Curt Ball Mounts - Fixed Ball Mount - C45250 Review
- Video: Review of Gen-Y Hitch Trailer Hitch Ball Mount - Adjustable Ball Mount - 325-GH-12001
- Video: Curt Rebellion XD Shock Absorbing Adjustable Ball Mount Review
- Video: Gen-Y Glyder Shock Absorbing Ball Mount Review
Jeff J.
5/5/2024
On your web page for this product the there is an etrailer video review by Jeff describing this hitch. In it he clearly states that the mount can only be used in the drop position (about the 1:00 mark in the video). I was really hoping that the ball platform could be inverted so this hitch becomes a 2" rise as mentioned in the above question. Can you confirm that it is possible to flip the ball platform in spite of what Jeff says in the video? Thanks, Jeff Jones