How to Install the Bulldog Replacement Sidewind Handle and Gear Kit
Question:
How do I install the Replacement Sidewind Handle and Gear Kit for 2,000 lb Bulldog Round Jacks, # BD500256.
asked by: Ed
Expert Reply:
Installing the gears is fairly easy, You will need to remove the cap at the top of the jack. The handle and gear are held in place with a roll pin that will need to be removed. You can then remove the handle, square block and gear.
You can then remove the bottom gear by lifting it out. If the bottom roll pin is damaged remove it also and the washer can be replaced after removing the lower pin. I added a photo showing the inside of a Bulldog jack with an external gear box, like part # BD155157, so you could easily see the orientation of parts. If you have a jack with internal gears, like part # BD151109, you will have to work from the opening in the top of the jack.
When replacing the bottom gear on the roll pin be sure to use the shorter pin and that the pin is in the slotted portion of the gear with the closed end groove that will not allow the pin to come out of the side of the gear, see photo. Reassemble in reverse order.
The top gear and bottom gear are the same, you just need to orient the gears correctly with the roll pins.
Products Referenced in This Question
Bulldog Round, Snap-Ring Swivel Jack - Sidewind - 10" Lift - 2,000 lbs - Zinc Finish
- Trailer Jack
- Car Hauler
- Enclosed Trailer
- Utility Trailer
- Leveling Jacks
- Tongue Jacks
- Steel
- 1001 - 2000 lbs
- Sidewind Jack
- Swivel Jack
- 10 Inch Lift
- Weld-On
- With Rectangle Foot
- Bulldog
more information >
Bulldog Round, A-Frame Jack w/ External Gearbox - Sidewind - 13" Lift - 2,000 lbs
- Trailer Jack
- Car Hauler
- Enclosed Trailer
- Utility Trailer
- A-Frame Jack
- Leveling Jacks
- Tongue Jacks
- Steel
- 1001 - 2000 lbs
- Sidewind Jack
- 13 Inch Lift
- Bolt-On
- Weld-On
- No Wheel or Foot
- Bulldog
more information >
Product Page this Question was Asked From
Replacement Sidewind Handle and Gear Kit for Bulldog Round Jacks - 2,000 lbs
- Accessories and Parts
- Camper Jacks
- Trailer Jack
- Handles and Cranks
- Sidewind
- Bulldog
more information >
Continue Researching
- Q&A: Replacement Wheel For Trailer Jack On Eagle Trailer
- Shop: Replacement Tube Cap for Bulldog Round Jacks with a Sidewind Handle
- Shop: Replacement Sidewind Handle and Gear Kit for Bulldog Round Jacks - 2,000 lbs
- Shop: Bulldog Round, Snap-Ring Swivel Jack - Sidewind - 10" Lift - 2,000 lbs - Zinc Finish
- Shop: Grease Seals 10-36 (pair)
- Search Results: 44649
- Article: Trailer Wiring Diagrams
- Q&A: Trailer Suspension Hanger Kit for Slipper Springs and 38 inch Wheelbase
- Shop: Trailer Hitch
- Q&A: Recommended Replacement for Atwood Surge Brake Actuator 85778
- Search Results: 25580
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Video: Choosing the Right Trailer Wiring
- Shop: Trailer Wiring
- Shop: etrailer Electric Trailer Brakes - 12" - Left/Right Hand Assemblies - 5,200 lbs to 7,000 lbs
- Video: Titan Trailer Brakes T2385200 Review
- Q&A: Towing a Trailer with Electric Brakes with a Semi Tractor with Air Brakes
- Shop: Hub Bearing Kit for Lippert, Dexter, and AL-KO Axles - 3,500 lb with #84 Spindle
- Shop: Fifth Wheel Hitch
- Search Results: 68149
- Article: Trailer Tire Sizing
- Shop: Gooseneck Hitch
- Q&A: Replacement Hub Needed for Lippert 122093 Hub on 5,200 lbs Axle
- Shop: Dust Cap for Kodiak Disc Brake Kit
- Video: Solera Replacement Awning Fabric Measurement and Installation
- Search Results: dust cap
- Video: Timbren Axle-Less Trailer Suspension System Installation
- Shop: Brake Controller
- Search Results: 15123
- Q&A: Replacement 5 Leaf Slipper Spring for a Tandem Axle Dump Trailer with Two 6K Axles