Replacement Hitch Pin and Clip for Swagman XC2 Bike Rack

Question

Question:

I purchase a swagman xc2 bike rack and unfortunately bent the safety pin for the hitch pin. Would you know how or where I can find a replacement hitch and hitch pin ? Thank you

asked by: Melvin M

0

Expert Reply:

It sounds like you are looking for the Replacement Threaded Hitch Pin and Clip part # P5902 which is correct for a Swagman XC2 Bike Rack. If this is not it please just let me know.

expert reply by: Conner L

0

Answer 1

The Replacement Hitch Tite Anti-Rattle Hitch Pin for Saris Bike Racks part #SA3021 uses a 1/2"-13 bolt. I am not sure what you mean by pin diameter as the above is a bolt, not a pin but if this was not the information you were looking for please…

view full answer...

Answer 2

The hitch pin bolt you'll need for a Thule bike carrier/rack is the Replacement Threaded Pin for Thule part #853-5917. It is indeed an M12x1.75 bolt which is roughly 4" long. I can't confirm compatibility of thread pitch for the…

view full answer...

Answer 3

All Thule bike racks use the same threaded hitch pin so you can use the Replacement Threaded Pin for Thule Snug Tite Hitch Lock and Anti-Rattle Device #853-5917. This is just the threaded bolt, and you'll need to use the flat washer, lock washer…

view full answer...

Answer 4

Swagman does not recommend using their G10 on the rear of a motorhome because the folding mechanism that allows the rack to fold up against the rear of the tow vehicle simply is not strong enough to deal with the additional jarring experienced when a…

view full answer...

Answer 5

You need the Swagman Replacement 1-1/4 and 2-Inch Shank for Swagman XC Series Bike Carriers, part #P306. This will allow your older XC hitch rack to remain in service in both 1-1/4- and 2-inch hitch sizes, thanks to the kit including an adapter…

view full answer...

Answer 6

The section under the head of the hitch pin bolt part #HRHPN-13 that you referenced measures 4 inches.

view full answer...

Answer 7

The 4 holes in the back of the MB Sturgis #108220 2-stage regulator are indeed for mounting. The holes aren't threaded but the metal is soft enough that a #8 1/4 inch machine screw would cut threads perfectly into it.

view full answer...

Answer 8

I do have an option for you but the quick-disconnect ports on the sides of trailers can only be used with accessories without built-in regulators. The majority of stoves and grills have these built-in regulators so the port on the side of the trailer…

view full answer...

Answer 9

Since your Coleman grill should have a built-in regulator you actually don't have to have one to change your propane to low pressure. If you are just needing the one T connection and you plan on only using it for your Coleman then you may be…

view full answer...

Answer 10

Since you want to keep the regulators on your fire pit and grill you will want to place a tee before the regulator on your RV's propane line. Most people are switching to quick disconnect so I recommend using the MB Sturgis Sturgi-Stay T-Fitting…

view full answer...

Answer 11

Of the two options the MB Sturgis Sturgi-Stay T-Fitting for POL Valve part #103537-MBS has two of the 250 quick disconnects which you will find on a ton of RV accessories. The Camco Brass Propane Tee w/ 4 Ports part #CAM59113 has a 1"-20 Male…

view full answer...

Answer 12

Based on my research it looks like the Nexgrill Fortress Table Top Grill comes with a regulator and Type 1 fitting and we have exactly what you need in order to attach this to your quick disconnect. The first thing you'll need is MB Sturgis Quick…

view full answer...

Replacement Hitch Pin and Clip for Swagman XC2 Bike Rack

Product Page this Question was Asked From

Continue Researching