Inner Tube Spare for Yakima Rack and Roll Trailer

Question

Question:

Im going on a Kayak trip in 1 week and I would like to have a spare tire.It seems like the Yakima replacements are back ordered until Feb. Is there another make of wheel and tire I can use as a spare. Thanks

asked by: Jack C

0

Expert Reply:

An easy backup solution for your Yakima Rack and Roll trailer's wheel and tire setup would be a replacement inner tube part # Y8880283 which stores much easier than a wheel and tire and would be what would most likely fail in unlikely event the wheel/tire gives you trouble. This is currently available.

expert reply by: Jameson C

0

Answer 1

A motorcycle shop should have no problem replacing the inner tubes of your Rack and Roll Trailer part #Y08106 with new ones like part #Y8880283. Sounds like you may have went to bicycle shops already. These tire setups are more like motorcycle setups…

view full answer...

Answer 2

The etrailer A-Frame Trailer Coupler w/ Round Jack Hole #CA-5280-RB uses the standard a-frame angle of 50 degrees. The length from the rear of the coupler to where the coupler meets its narrowest point is approximately 9" long. I have include…

view full answer...

Answer 3

If you are already planning on needing more space than the 66" Yakima Rack and Roll Trailer #Y08106 can provide then I highly recommend going ahead and getting the 78" Rack and Roll #Y08107 instead. The 78" trailer is a whole foot…

view full answer...

Answer 4

The inner tubes of the Yakima Rack and Roll #Y08106 wouldn't wear out quicker than the tread tire. Trailer tires should be replaced at 6 years so when you get to that point I'd go with the new #Y8880282 and a new inner tube part #Y8880283.

view full answer...

Answer 5

view full answer...

Answer 6

Yakima Replacement Inner Tube #Y8880283 fits the 3.25-16 tire #Y8880282 used on the Rack and Roll trailer #Y08106. This 16-inch inner tube is rated for the tire's required 40-psi pressure.

view full answer...

Answer 7

Since we have started carrying the Yakima Rack and Roll trailer #Y08107 I have not heard any complaints regarding the wheel bearings failing and only a few instances where people wanted to replace the wheel assembly. If you need to replace your…

view full answer...

Answer 8

While there isn't a life expectancy, per se, of the shocks on the Yakima Rack and Roll Trailer - 66" #Y08106 and 78" #Y08107, upgrading to the HD shocks is absolutely a good idea if your gear weighs around 200 llbs and certainly…

view full answer...

Answer 9

The Replacement Inner Tube for Wheel on Yakima Rack and Roll Trailers - Qty 1 #Y8880283 does have a TR-4 valve stem. I reached out to my contact at Yakima to confirm.

view full answer...

Answer 10

According to Yakima, the Heavy Duty Shocks for Yakima Rack and Roll Trailer #Y08110 should only be used if you add the 78" crossmember kit #Y08111. They didn't have an exact reason for this, but it sounds like the concern is people will…

view full answer...

Answer 11

The Yakima Rack and Roll trailer part #Y08106 doesn't have any safe jacking points on it so if you were in need of changing the spare you'd have to remove the kayak and raise the trailer by hand.

view full answer...

Answer 12

The Yakima Rack n Roll trailer shocks #Y08110 have 4 inches of vertical adjustability. To adjust them you will need to turn the bottom-most orange piece. There are several notches and turning the orange part clockwise makes them longer. I have…

view full answer...

Inner Tube Spare for Yakima Rack and Roll Trailer

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching