What Would be Needed to Change Trailer Wheel and Tire if On Side of Road

Question

Question:

What do I need to change a tire on my Grand Design 2500RL if Im on the side of the road?

asked by: Fabian G

0

Expert Reply:

You'd need a high capacity bottle jack like the Powerbuilt part # ALL647501 which has a 24,000 lb capacity. You'd also want a 4-way wrench for installing and removing the lug nuts. If you need a spare wheel and tire let me know what tire size you have and your wheel bolt pattern.

expert reply by: Jameson C

0

Answer 1

I recommend the TowSmart Folding 4-Way Lug Wrench #3481281 as our best 4-way. This is easily folded to reduce the amount of space it takes up. It has an 11/16", 3/4" and 13/16" sockets fixed to 3 ends with a 1/2" drive on the 4th…

view full answer...

Answer 2

The Powerbuilt Bottle Jack #ALL647501 that you referenced weighs 14 lbs and has a 24,000 lb weight capacity.

view full answer...

Answer 3

Scissor jacks for trailers or RVs such as #TJSC-24 are not meant to lift the trailer/RV off the ground. They are meant as support only. What I recommend is a bottle jack such as #ALL647501. This is a 24,000 pound jack that has a lift range of 8-1/4…

view full answer...

Answer 4

The Powerbuilt Unijack - 21" Lift - 6,000 lbs #ALL620471, is perfect for your 2013 Ford Kuga. The jack should be placed under the frame as close to the wheel as possible with the frame fully in contact with the jack. This jack has a lift range…

view full answer...

Answer 5

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 6

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 7

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 8

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 9

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 10

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 11

We have one option that will work for you. The Trailer Hub and Drum Assembly - 4,400-lb E-Z Lube Axles - 10" Diameter - 6 on 5-1/2 #8-407-5UC3-EZ uses inner bearing #L68149 and outer bearing #LM67048 so it would work perfectly on your spindle.…

view full answer...

Answer 12

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

What Would be Needed to Change Trailer Wheel and Tire if On Side of Road

Product Page this Question was Asked From

Continue Researching