Replacement 3 inch and 1.5 inch Valve for Winnebago Spyder

Question

Question:

I have a 3x1.5 valve I need to replace on my winnebago spyder I can’t quite find what I need to replace it from you guys. Can I send a picture of my setup and you guys can point me in the right direction to replace it? Do you guys ship to Canada as well?

asked by: Jeff A

0

Expert Reply:

The Bristol RV Waste Valve # 34466N3AR will fit the setup you sent in a picture of. Only thing else you'll need is ABS Solvent part # 3447530889 and you'd be set.

We do ship to Canada.

expert reply by: Jameson C

0

click to enlarge

Answer 1

I looked up the Bristol V33B2R and the correct replacement is the Bristol RV Waste Valve - Sewer Wye - Rotating - 3" and 1.5" Hubs to 3" Lug #34466N3AR which has the hub style fittings for the 3 inch and the 1.5 inch sections which…

view full answer...

Answer 2

Yes, you can replace the 3" and 1-1/2" valves on your Bristol Double RV Waste Valves - Elbow - Rotating - 3" and 1.5" Hubs to 3" Spigot #34466ND14AAR with the Bristol Waste Valve Body for RV Gray Water w/ Coupler, Seals, and…

view full answer...

Answer 3

To replace your current double waste valve you'll just need the Double RV Waste Valves - Heel Inlet - Rotating - 3" Hub and 1-1/2" Hub #T68 and some Valterra ABS Solvent Cement - 1/4 Pint #A05-0303 for a secure connection.

view full answer...

Answer 4

The part you're needing for your Bristol Double RV Waste Valves #34466ND15AAR is a hub so you'll want the LaSalle Bristol RV Sewer Slip Hub with Flange #34466V1515. The difference between the #34466V1515 (hub) and #34466V1515S (spigot) is how…

view full answer...

Answer 5

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 6

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 7

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 8

The Trailer Leaf Spring, 2250 lbs. 6 Leaf, item #e27SR, is sold as a replacement spring for older trailers and measures 26 inches for eye to eye, center to center. If you are replacing the springs and hangers you will need to use the same center to…

view full answer...

Answer 9

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 10

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 11

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 12

It really just depends on what the wires are for. Most likely you have several ground wires among the 8 as well as a couple running light circuits in there as well. You just have to run all of the wires to the correct circuits. The 4-way wiring of…

view full answer...

Replacement 3 inch and 1.5 inch Valve for Winnebago Spyder

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching