Can The Frame Of the Trailer Be Installed In the Slot On the Scissor Stabilizer Jack

Question

Question:

TJSC-24 What is the dimension of the width between the two bracket wings. Im wondering if the width of my camper frame, 1 5/8, will fit in that slot. Thank you

asked by: Ken R

0

Expert Reply:

In regards to the Scissor Stabilizer Jack part # TJSC-24, the slot is not designed to support the frame. I must recommend you attach the two ears to the bottom of the frame as you can see in the attached video. I have also attached for you some general dimensions of said ears below as well.

expert reply by: Conner L

0

click to enlarge

Answer 1

For a replacement jack for your 2021 Jayco Jay Flight SLX 7 174 BH I recommend the Stabilizer Jack - 6-1/4" Drop Leg Travel - 18" - 650 lbs #TJ01RT. This jack same mounting hole dimensions as your current jack at 3 inches apart on center.…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

The Thor Motorhomes have a big tire and the only hitch mounted spare tire carrier we have for it is the Roadmaster Hitch Mounted Spare Tire Carrier w/ 2" Receiver Opening item #RM-195225. This carrier holds 16" to 24-1/2" spares with…

view full answer...

Answer 4

The difference between the item #RM-195125 and the item #RM-195225 is that they are designed for different sized wheels. The item #RM-195125 is designed to handle up to 16.5" tall wheels where as the item #RM-195225 can hold between 16" and…

view full answer...

Answer 5

Yes, there is! You have to make a small 2" x 3-1/8" cut in the trim below the bumper for the 2" receiver of the etrailer item #e45ZR to stick through. I have linked the installation instructions below along with an installation video…

view full answer...

Answer 6

The 2021 Kia Tellurides all come with the factory tow package port that the Curt T-Connector Vehicle Wiring Harness part #CU94FR plugs into. It does not have to come equipped with the factory tow package per se. It's a direct plug-in fit for all…

view full answer...

Answer 7

Hello Al. The Scissor Stabilizer Jack #TJSC-24 has a retracted height of 5". Meaning if the current jacks are at 5-3/4" you will gain 3/4" of clearance. if you are looking to gain as much clearance as possible, I suggest you take a…

view full answer...

Answer 8

I typically just reuse the same hardware as long as it isn't rusting out and the threads are still good when swapping out scissor jacks, like the #TJSC-24. Scissor jacks typically won't come with any hardware so if your current hardware is…

view full answer...

Answer 9

Hey Jaime, yes you can replace your 25-1/4 inch 3,500 lb axle leaf springs with a 5k rated axle spring like the part #e44SR. This will increase the suspension's weight capacity and might make the ride quality a little rougher but it would fit and…

view full answer...

Answer 10

Hey Kevin thanks for your question. There is not much downside to going with the 5,000 lb springs instead of the 3,500 lb. A higher rated spring may make the ride a bit more "chunky" at times, since the spring would not flex as easily.…

view full answer...

Answer 11

Yes, the Ultra-Fab Ultra Scissor Jack #UF48-979006 will work as a replacement for your damaged stabilizer on your 2019 Keystone Hideout 274LHS. This jack has a universal style bolt mounting plate and an oversized footplate to prevent it from sinking…

view full answer...

Answer 12

The Lippert Flow Max RV Toilet #LC67AF is absolutely a good option for part-time RVers who store their RV for months. The supply vale and the seal are both standard.

view full answer...

Can The Frame Of the Trailer Be Installed In the Slot On the Scissor Stabilizer Jack

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching