Fit and Installation of Curt C13395 Class III Trailer Hitch on 2019 Jeep Cherokee Latitude
Question:
I have a 2019 Jeep Cherokee latitude. Would the trailer hitch C13395 fit to this model fairly easy? Thanks
asked by: Travis J
Expert Reply:
It sure will! On a scale of 1 to 10, we rated the install as a 5 which isn't too bad. The exhaust needs to be temporarily removed at the rear of the vehicle, but it's not terribly difficult if you follow the instructions and install video I've linked for you. The video will walk you right through the process.
If you are planning on towing you will also need a wiring harness item # C56406 and a ball mount kit item # C45534.
I've also linked to the installation instructions and a video for the trailer wiring harness.
Products Referenced in This Question
1-7/8" Hitch Ball - 1" Diameter x 2-1/8" Long Shank - Chrome - 2,000 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 1-7/8 Inch Diameter Ball
- 2-1/8 Inch Shank Length
- 1 Inch Diameter Shank
- 2000 lbs GTW
- Class III
- Draw-Tite
more information >
2" Hitch Ball - 1" Diameter x 2-1/8" Long Shank - Chrome - 7,500 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 2 Inch Diameter Ball
- 2-1/8 Inch Shank Length
- 1 Inch Diameter Shank
- 7500 lbs GTW
- Class III
- Tow Ready
more information >
Curt Towing Starter Kit for 2" Hitches - 2" Ball - 3/4" Rise, 2" Drop - 7.5K
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- 2 Inch Ball
- One Ball
- Steel Ball
- Steel Shank - Gloss Black
- Drop - 2 Inch
- Rise - 0 Inch
- Fits 2 Inch Hitch
- 7500 lbs GTW
- Class III
- Ball Mount Kit
- CURT
more information >
Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Powered Converter
- Custom Fit
- 4 Flat
- CURT
more information >
Curt Ball Mount for 2" Hitches - 4" Rise, 6" Drop - 14-1/4" Long - 6,000 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 1 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Drop - 6 Inch
- Rise - 4 Inch
- Fits 2 Inch Hitch
- 6000 lbs GTW
- Class III
- Long Shank
- CURT
more information >
Pin and Clip for 2" and 2-1/2" Hitches - 5/8" Diameter x 3-1/4" Span
- Hitch Pins and Clips
- Standard Hitch Pin
- Fits 2 Inch Hitch
- Fits 2-1/2 Inch Hitch
- 5/8 Inch Diameter
- 4 Inch Span
- Draw-Tite
more information >
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 675 lbs TW
- 4500 lbs GTW
- 5500 lbs WD GTW
- 2 Inch Hitch
- 750 lbs WD TW
- Concealed Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Q&A: How to Tell If MORryde Rubber Equalizers Will Fit Trailer
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: Correct Replacement for AL-KO 7230 Hub/Drum and Brakes
- Article: 7 Common Questions Everyone Has About Trailer Tires
- Q&A: When to Replace Dexter Nev-R-Lube Bearings
- Q&A: Is Bow in 3,500 lb Trailer Axle Enough Camber for Loaded and Unloaded Trailers
- Q&A: Measurements Needed to Determine Replacement Bearings Without Having Old Bearings Numbers
- Q&A: Flat Tow Set Up for 2022 GMC Yukon XL
- Q&A: 2021 GMC Yukon XL AT4 Flat Towing Components
- Article: Must Have RV Accessories that Will Make or Break Your Trip
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Article: Trailer Wiring Diagrams
- Article: How Harvest Hosts Is Becoming the New Standard of the Camping Industry
- Article: How to Choose the Right Trailer Hitch Class