Is There a Required Mounting Hole Spacing for the Buyers Products Sliding Winch Track # 3371903040

Question

Question:

When bolting the track on is there a preferred or recommended spacing for the bolts?

asked by: Jason P

0

Expert Reply:

The Buyers Products Sliding Winch Track # 3371903040 that you referenced has mounting holes pre-drilled near the ends of the track but if you wanted to use a different set of holes you certainly could. There isn't a requirement for where they would have to be. The track is 72 inches overall.

expert reply by: Jameson C

0

Answer 1

Yes, the Buyers Products Sliding Winch Track #3371903040 can be installed on a flat steel surface to secure a load, as you mentioned. Since it's designed to allow a winch to slide along that channel, for this purpose, the channel must face down.…

view full answer...

Answer 2

Yes, the Buyers Products Sliding Winch Track 1/4" x 72" part #3371903040 can be bolted to the trailer and that is actually the manufacturers preferred method for installation. However, in order to avoid any interference with the track…

view full answer...

Answer 3

The Lock Side-Door Bar Lock Assembly, #305736, is designed so that when it is installed, it pushes the door tightly closed. The unit is not adjustable. Attempting to bend or heat the components could compromise the structural integrity of the unit.

view full answer...

Answer 4

That would depend on several different factors such how much the door sticks out away from the trailer and how much the handle sticks out away from the door. However, if you do run into clearance issues you can always install a spacer on the hinge…

view full answer...

Answer 5

The Redline 36 Inch Side-Door Bar Lock Assembly, #305736, can be used on the right and left side. The image on our product page shows it in the left hand orientation, but it can be used on the right hand side by flipping it upside down. Check out the…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 10

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Is There a Required Mounting Hole Spacing for the Buyers Products Sliding Winch Track # 3371903040

Product Page this Question was Asked From

Continue Researching