Does Curt Trailer Hitch Receiver 13352 fit 2005 Ford F-150 XL With Long Bed

Question

Question:

I have a 2005 ford xl regular cab long box with a V6 and manual 5 speed transmission. Just verifying this hitch will fit. Thanks

asked by: Derek J

0

Expert Reply:

Yes it does! I can confirm the Curt Trailer Hitch Receiver # C13352 will fit your 2005 Ford F-150 XL with a long bed, V6 engine and manual transmission. The only thing it would not fit is if you already had the factory trailer hitch on your F-150.

I have added a link to a video install for you to check out as well of the Curt Trailer Hitch # C13352 on a 2005 Ford F-150.

expert reply by: Kyle S

0

click to enlarge

Answer 1

Yes, my technical contact at Curt Mfg. verified that the Class III receiver hitch, #C13352, will fit on your 2004 Ford F150 styleside (stepside) pickup as long as it is the new body style truck and not the Heritage series truck which is the old body…

view full answer...

Answer 2

I went out to the warehouse and pulled a Curt 2 Inch Bumper Hitch, #E-3S, to take some measurements. The center to center distance between the two round holes is 6 inches. They measure 5-7/16 inches apart, inside edge to inside edge. They are 9/16…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Answer 5

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 6

Brake systems are not dependent on the hub bolt pattern. So you can use the Electric Trailer Brake Kit #AKEBRK-7-SA for 12 inch hub/drums or #AKEBRK-35-SA for 10 inch hub/drums. Then use #10-1-1 wire sold by the foot for your brake magnet wiring.…

view full answer...

Answer 7

Normal operating temperatures for drum brakes range from 150-400 degrees F. During certain stopping conditions the brake heat can exceed 600 degrees. The effectiveness and stopping power of the brakes is significantly reduced at these higher…

view full answer...

Answer 8

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.

view full answer...

Answer 11

The AL-KO trailer hub part number 8700 that you have is a 3,500 lb trailer hub/drum with a 5 on 4-1/2 inch bolt pattern. Based on that the #AKHD-545-35-EZ-K is the correct fit and would work great.

view full answer...

Answer 12

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Does Curt Trailer Hitch Receiver 13352 fit 2005 Ford F-150 XL With Long Bed

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching