Easiest Solution for Installing 7-Way and Brake Controller in 2018 Jeep Wrangler Unlimited
Question:
Best way to add a 7pin connection to a 2018 JLU sport without factory tow package. Also easiest way to add brake controller. Cost not a factor.
asked by: Mario B
Expert Reply:
I have just the simple solution you are looking for to easily add a 7-way and brake controller to your 2018 Jeep Wrangler JL Unlimited...
Basically you have to start out first with a 4-way which covers the lighting circuits of the trailer wiring. For that the easiest and most reliable solution is the Curt kit part # C56407 which installs by plugging inline with the taillight connectors of the Jeep. I attached an install video to use as a guide for this to make it as easy as possible.
So then the easiest to install brake controller that also works really well is the Curt Echo Mobile part # C51180. Basically this just plugs into an active 7-way and once you sync it to your phone it's ready to go. I don't think an easier option could be possible. This brake controller is proportional too which means it senses the amount of deceleration your tow vehicle is applying and applies the trailer brakes in a relative way.
To convert the 4-way to a 7-way so that you can install the brake controller only requires the 7-way adapter kit part # ETBC7L. The 4-way of this plugs into the 4-way of your vehicle and once you run the included wiring and breaker up to the vehicle's positive battery post it's active enough to allow the Echo to function. This saves you from having to hardwire in a brake controller which requires tapping into the brake signal of your vehicle and running a few other wires too.
Products Referenced in This Question
Curt Echo Wireless Brake Controller - 7-Way Plug Mount w/ Bluetooth App - 1 to 2 Axle - Proportional
- Trailer Brake Controller
- Proportional Controller
- Hidden
- Up to 2 Axles
- Smartphone Display
- CURT
more information >
7-Way RV Upgrade Kit for Trailer Brake Controller Installation - 12 Gauge Wires
- Accessories and Parts
- Trailer Brake Controller
- Installation Kits
- etrailer
more information >
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 350 lbs TW
- 3500 lbs GTW
- 4000 lbs WD GTW
- 2 Inch Hitch
- 400 lbs WD TW
- No Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Q&A: Comparing Curt and Tekonsha Trailer Wiring Harness for 2018 Jeep Wrangler Unlimited
- Q&A: Can Hole in Bumper Fascia from Installing EcoHitch Be Covered on 2021 Tesla Model 3
- Article: How to Choose the Right Trailer Hitch Class
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: How to Measure for Trailer Hitch Drop
- Q&A: Curt Trailer Hitch # C13392 And # 13432 TW and GTW Capacities
- Article: My Trailer Hitch Doesn't Fit
- Article: Flat Towing Package for 2020 Jeep Wrangler
- Article: Electric Brake Controller Installation on Dodge Ram Trucks to 2012
- Q&A: Kuat Pivot 2 Swing Away Hitch Extender # PVD20B Weight Capacity
- Q&A: Choosing OEM or Aftermarket 5th Wheel Puck System for 2021 Ford F-250
- Q&A: Installation of Trailer Hitch on 2018 Jeep Wrangler JL with Additional Bracket at Frame
- Q&A: Replacement Oil and Grease Seals For PHLE AP3137N2 Oil Seal
- Article: Wiring Trailer Lights with a 6-Way Plug (It's Easier Than You Think)