Replacement Boat Trailer Winch for Winch Mounted In Channel On Frame
Question:
Hi there. Most winches are too wide for my trailer which has a recessed slot for the winch and a cutout for the handle. The current winch is a touch over 3 3/8 and just shy of 3 1/2 inches wide. The mounting holes are 4 1/8inch center to center, and down the middle of the winch. The handle axle is located 1 1/2inch from the nearest mounting hole, and 1 7/8inch from the bottom of the plate to the center of the handle axle. This winch looks like a promising option. Do you have anything else that will fit these dimensions? It may be difficult to see but ive attached a pic for reference.
asked by: Dave M
Expert Reply:
I do have plenty of options for you to choose from but finding one that matches what you have exactly is going to be next to impossible unless you were able to find the same model. Therefore, you are most likely gong to need to do a bit of modifications if you want to replace this winch. It looks like the winch mount setup you have now was a one-off for your particular winch model. The Fulton F2 Fully Enclosed Trailer Winch part # FW16000101 has a 6-3/16" long x 3-3/8" wide base but the mounting hole pattern is a bit different so you will need to re drill these holes as well as a new access hole for the handle shaft most likely.
The other option you have is to cut off the winch mount just after the trailer jack and then install the CE Smith Winch Stand part # CE31013G which is a much more feasible solution for you and what I recommend. The Fulton F2 Fully Enclosed Trailer Winch will then work with the CE Smith Winch Stand.
Products Referenced in This Question
CE Smith Winch Stand - Galvanized Steel - 30" Tall x 2" Wide
- Boat Trailer Parts
- Winch Stand
- 30 Inch Tall
- 2 Inch Wide
- CE Smith
more information >
Product Page this Question was Asked From
Fulton F2 Fully Enclosed Trailer Winch with Strap and Adjustable Handle - 1,600 lbs
- Trailer Winch
- Standard Hand Winch
- Boat Trailer Winch
- Utility Winch
- Standard Duty
- Standard Hand Crank
- Single Speed Winch
- Polyester Strap
- Fulton
more information >
Continue Researching
- Video: CE Smith Boat Trailer Parts - Winch Stand - CE31013G Review
- Shop: CE Smith Winch Stand - Galvanized Steel - 30" Tall x 2" Wide
- Shop: etrailer Hitch Pin Alignment Collar for Hitch Accessories - 2" Hitches
- Shop: Dutton-Lainson Angle Mounting Plate for StrongArm Electric Winches
- Search Results: d ring mount
- Shop: CE Smith Keel Roller Assembly for 2" Wide Trailer Tongues - Galvanized Steel and Black Rubber
- Video: Review of Dutton-Lainson - Trailer Winch - DL24059
- Search Results: ce smith bracket
- Search Results: now stop
- Search Results: winch mounting plate
- Search Results: f142306
- Search Results: bow stop
- Search Results: f2 fulton winch
- Video: CE Smith Boat Trailer Roller Shaft with Pal Nuts Review
- Video: Yates Rubber Boat Trailer Parts - Bow Guard - YRJONBLOCK Review
- Video: CE Smith Multi Sport Plus Boat Trailer with Bunks Review and Assembly
- Video: CE Smith Boat Trailer Parts - Roller and Bunk Parts - CE32005G Review
- Video: CE Smith Boat Trailer Parts - Roller and Bunk Parts - CE31005PG Review
- Article: Determining Trailer Tongue Weight
- Q&A: How Does the CE Smith Winch Stand # CE31013G Mount to Trailer
- Shop: Yakima Rack and Roll Trailer - 78"
- Q&A: How To Mount an Electric Boat Trailer Winch
- Shop: Roadmaster Dual Hitch Receiver Adapter, 2" or 4" Drop/Rise
- Shop: etrailer Tongue Weight Scale for Campers and Utility Trailers - 2,000-lb Capacity
- Q&A: Winch that Could Fit in CE Smith Bow Roller Bracket # CE31005PG
- Q&A: Mounting Plates for Dutton-Lainson StrongArm Electric Trailer Winch, # DL25200
- Q&A: Replacement Bow Roller Brackets for Boat Trailer
- Q&A: Bow Stop Setup Availability for a Boat Trailer
- Q&A: Bow Roller and Mounting Bracket Recommendations for Boat Trailer
- Shop: Towing Mirrors