7-Way and Brake Controller Install Info for 2018 Chevy Express Van
Question:
2018 chevy 2500 express ,i believe it set up for trailer ...there is an oval plu under rear , for 7 pin?? i need to hook up for trailer brakes , im hoping wiring is run and there are plugs up front as well .????
asked by: CHRIS L
Expert Reply:
Since your 2018 Chevy Express Van has a round connector present under the rear of it for a 7-way like the part # A10-7072VP to plug into you do have the tow package.
Vehicles like yours with the 7-Way tow package have the blue output brake wire already ran from the back to the front. It is located under the dash near the emergency brake pedal. Some models will have the connection wiring taped and tucked under the driver side floor mat up towards the firewall.
Next, for a wiring kit to install the brake controller to the 7-way you would want the Wiring Kit for 2 and 4 Brake Electric Brake Controllers # 5506. This will provide the power source and ground for the wiring for the brake controller. You will need to test the wires from the brake pedal switch of your vehicle to find a circuit that has voltage when the brakes are applied and none when not applied. This will be the circuit you will run the red wire to.
Finally you will need to run a length of 10 gauge wire (part # 10-1-1) from the brake output circuit of the controller to the brake output circuit of the 7-way (blue wire). The # 10-1-1 is sold by the foot so you will need to order a quantity of the amount of feet you will need.
For a brake controller I would recommend the Prodigy P2 Brake Controller part # 90885. This is our best selling brake controller because of how well it works and how easy it is to set up.
I attached an install video that shows how a similar brake controller installs in a similar Express van as yours for you to check out as well. You might check to see if you find the wiring like what's seen in the video as well. If this is the case you don't need the # 5506 or the # 10-1-1.
Products Referenced in This Question
Wiring Kit for 2, 4, 6, and 8 Brake Electric Trailer Brake Controllers
- Accessories and Parts
- Trailer Brake Controller
- Installation Kits
- etrailer
more information >
Tekonsha Prodigy P2 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Trailer Brake Controller
- Proportional Controller
- Electric
- Electric over Hydraulic
- Automatic Leveling
- Under-Dash Box
- Dash Mount
- Up to 4 Axles
- LED Display
- Up to 360 Degrees
- Tekonsha
more information >
Mighty Cord Replacement 7-Way RV Style Trailer Connector for Factory Tow Package - Vehicle End
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Custom Fit
- 7 Round - Blade
- Mighty Cord
more information >
Product Page this Question was Asked From
Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Accessories and Parts
- Trailer Brake Controller
- Installation Kits
- etrailer
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: Brake Controller Installation: Starting from Scratch
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Article: Trailer Wiring Diagrams
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Article: Towing a Trailer? Let's Talk About Brake Controllers
- Article: How to Choose the Right Trailer Hitch Class
- Article: How to Measure for Trailer Hitch Drop
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Q&A: Where Do the Wires on the Universal Install Kit for Trailer Brake Controllers Get Installed?
- Q&A: 2022 Toyota Highlander Wiring for a 7-Way Blade Connector
- Q&A: Should I Get a Proportional or Time-Delayed Brake Controller
- Q&A: Parts Needed to Tow Trailer With Brakes Using 1992 Dodge D250
- Q&A: 4-Flat Trailer Wiring For 2024 Jeep Wrangler With Tow Bar Wiring