Troubleshooting Trailer Suspension Bolts Splines that Aren't Seating
Question:
I Purchased these bolts and shackle straps 115052Galv. Having a very hard time getting the spines to draw into the straps and the hangers on the trailer. All holes are 9/16 and I used a 9/16 drill bit to ensure the holes did not have buildup or burs. Im putting a lot of torque on the nut to try and get the bolt to draw in and sit flush. I was able to get two to draw in without that much torque but others will not budge forward with a lot of torque. Is there a trick to getting these to draw in? Do I need to hit the nuts with an impact?
asked by: Steve L
Expert Reply:
Have you tried tapping the bolt in with a hammer? Hopefully not much force would be needed. Ideally you get the splines seated all the way but then you don't have to really torque the nuts down as the bolt needs to allow the suspension to move. You might open up the holes a bit more to allow the splines to fit through if they are being stubborn.
Product Page this Question was Asked From
Zinc Shackle Bolt with Locknut for Double-Eye Springs - 3" Long
- Trailer Leaf Spring Suspension
- Suspension Bolts
- Boat Trailer
- Snowmobile Trailer
- 9/16 Inch Diameter
- 3 Inch Long
- TruRyde
more information >
Continue Researching
- Q&A: Will 14" Diameter Trailer Wheels fit On The DeeMaxx Disc Brake Kit # DE66YR?
- Video: DeeMaxx Disc Brake Kit Review
- Search Results: leaf spring bushing
- Shop: Zinc Shackle Bolt with Locknut for Double-Eye Springs - 3" Long
- Shop: Nylon Bushing - 1/2" Inner Diameter, 7/8" Outer Diameter - 1-3/4" Long
- Search Results: light bracket
- Shop: Spring-Eye Bolt with Locknut for Slipper Springs - 3-1/2" Long
- Video: Review of TruRyde Trailer Leaf Spring Suspension - Suspension Bolt and Locknut - TRFA73Z916DLNZ
- Video: Kodiak Disc Brake Kit Installation K2R35D
- Search Results: trailer hubs
- Search Results: shackle bushing
- Search Results: trailer axle hubs
- Video: Review of Lippert Trailer Leaf Spring Suspension - Bronze Bushing - LC32SV
- Video: etrailer Trailer Idler Hub Assembly Installation
- Video: Review of DeeMaxx Trailer Brakes - 3.5K 10 Inch Maxx Coat Disc Brake Assembly - DE89YR
- Video: Review of DeeMaxx Trailer Brakes - 3.5K Slip-On Rotor Disc Brake Kit - DE42FR
- Search Results: grommet
- Q&A: How to Convert Trailer Drum Brakes Over to Disc Brakes
- Q&A: What Direction Should Disc Brake Calipers Face
- Q&A: Selecting a Surge Coupler for a Boat Trailer
- Search Results: leaf spring hanger
- Shop: Kodiak Hydraulic Brake Line Kit - Tandem Axle - 20'
- Shop: Snap Bushing Grommet - 7/16" ID, 9/16" OD
- Shop: DeeMaxx Disc Brake Kit w/ Mechanical Brake - 10" Hub/Rotor - 5 on 4-1/2 - 3,500 lbs
- Shop: Hydrastar Vented Marine Electric Over Hydraulic Actuator for Disc Brakes - 1,600 psi
- Q&A: Correct Bushing and Bolt for 4-Leaf Slipper Spring # e33SR
- Q&A: Should Leaf Spring Capacity Match Trailer Weight or Axle Weight for Best Ride Comfort
- Q&A: Replacement 26 Slipper Spring for Sea Lion Trailer
- Article: How to Tell the Weight Rating of a Trailer Axle
- Shop: RV Jack Pads