Solution for Stripped Weld Nut When Installing Trailer Hitch
Question:
The 1.75 mm bolt or weld nut on my 2018 ford transit hitch is stripped. The nut turns but doesn’t tighten. Can I reinforce the hitch to the frame with U bolts w/straps? Do you sell taps and bolts in larger sizes?...thanks
asked by: Joseph C
Expert Reply:
If you can access an open end of the frame where the weld nut broke off you could fishwire a new carriage bolt in place of the weldnut. Otherwise you may have to weld the hitch on or see if a local garage like you mentioned could come up with a way to re-weld in a weld nut.
For a bolt leader you could then use the # C58400. I attached a link to an install video that at the 1:30 mark shows how to fishwire hitch hardware. You will need to drill out the old weld nut.
Products Referenced in This Question
Curt Fish Wire Bolt Leader - 1/2"
- Accessories and Parts
- Fifth Wheel Installation Kit
- Gooseneck Installation Kit
- Trailer Hitch
- Tools
- Bolt Leader
- 1/2 Inch
- CURT
more information >
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Trailer Hitch
- Custom Fit Hitch
- Class I
- 200 lbs TW
- 2000 lbs GTW
- 1-1/4 Inch Hitch
- Visible Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Trailer Hitch
- Q&A: How to Install Trailer Hitch on Vehicle with Stripped Weld Nut
- Video: Trailer Hitch Installation - 2009 Ford Flex
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Q&A: Troubleshooting Stripped Weld Nuts on Trailer Hitch Installation
- Shop: Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Article: Trailer Wiring Diagrams
- Search Results: brake controller
- Shop: Trailer Wiring
- Q&A: Difference Between Wiring Harnesses for a 2009 Ford Flex
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Video: Choosing the Right Brake Controller
- Search Results: 18144
- Shop: Roof Rack
- Shop: Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Article: Roadmaster Vehicle Specific Base Plates
- Shop: Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Video: etrailer Class III Trailer Hitch Installation - 2019 Ford Flex
- Search Results: 118467
- Shop: Brake Controller
- Video: Tekonsha Trailer Wiring Harness Installation - 2019 Ford Flex
- Shop: Suspension Enhancement
- Shop: Base Plate for Tow Bar
- Video: Review of CURT Custom Fit Vehicle Wiring - 6 Pole Trailer Hitch Wiring - C55664
- Shop: Vehicle Tow Bar Wiring
- Article: How to Choose the Right Trailer Hitch Class
- Q&A: Correct Trailer Hitch for a 2011 Honda Crosstour
- Q&A: Recommended Trailer Hitch And Wiring For 2013 Honda Crosstour