What is Size of Metal Used for Upright Mast of Roadmaster Spare Tire Carrier # RM-195125

Question

Question:

Is the vertical tire mounted portion, 2 inch metal stock ?

asked by: Jim M

0

Expert Reply:

The vertical mast of the Roadmaster Spare Tire Carrier # RM-195125 that you referenced is made from 2 inch by 2 inch steel just like the shank of the carrier that fits into a 2 inch trailer hitch.

expert reply by: Jameson C

0

Answer 1

Yep, you're 100 percent on the money, Al. The 200 lb tongue weight capacity is only for what is put in the receiver and does NOT count the weight of the spare tire and the carrier itself for the Roadmaster Spare Tire Carrier #RM-195125.

view full answer...

Answer 2

Yes, the Roadmaster Spare Tire Carrier #RM-195125 can pivot to the left or right depending on what kind off clearance you have. We only show to the left in the video because there is a ladder on the right side, but if you check out the attached photo…

view full answer...

Answer 3

I reached out to Roadmaster, who told me the height from the center of the hitch to the top of the tire mount of the Roadmaster Spare Tire Carrier #RM-195125 is approximately 28-3/4" from the center of the hitch to the top of the tire mounting…

view full answer...

Answer 4

The Roadmaster Spare Tire Carrier part #RM-195125 isn't year, make, and model specific. It's designed for any vehicle with a 2" trailer hitch receiver with a bumper clearance of at least 6-3/4". In regards to spare tire compatibly,…

view full answer...

Answer 5

I don't have vehicle specific information that would allow me to definitively say that the carrier would allow the rear hatch to open fully, but I can certainly help you figure it out. To determine if you'll have clearance, you'll need to…

view full answer...

Answer 6

The Roadmaster Spare Tire Carrier #RM-195125 has an easy peasy adjustable mounting bracket to hold all wheels with a lug nut circle up to 8" so you will have a lemon squeezy time mounting your 17inch high x 8.5inch wide, with 5.75inch…

view full answer...

Answer 7

I checked with Roadmaster and they told me that from the center of the hitch pin to the other end of the hitch opening measures 14.88 inches.

view full answer...

Answer 8

To relocate your license plate if the Roadmaster Spare Tire Carrier #RM-195125 is blocking it, you can use the Optronics LED Trailer License Plate Light w/ Bracket - 5 Diodes - Clear Lens #LPL55CB. This bracket does come with a 5 diode light that you…

view full answer...

Answer 9

The Roadmaster Spare Tire Carrier part #RM-195125 can be used with a bike rack with swing-away adapter but each of the adapters are going to limit/reduce weight capacity. The Roadmaster Spare Tire Carrier in particular will reduce the tongue weight…

view full answer...

Answer 10

There seemed to be a few discrepancies with the measurement you requested, so I decided to go pull a Roadmaster Spare Tire Carrier #RM-195125 out of the box and check for myself. With that said, I did get completely different measurements. I included…

view full answer...

Answer 11

It is possible you will be able to put your truck's tailgate completely down when using the Roadmaster Spare Tire Carrier #RM-195125. The carrier comes down horizontally (see accompanying photo) to the side of the bumper, so it depends on the…

view full answer...

Answer 12

In order to determine if a hitch mounted accessory will clear the spare tire on the Roadmaster Spare Tire Carrier part #RM-195125 you will need to measure the distance from the center of the hitch pin hole to the closest part of said accessory. This…

view full answer...

What is Size of Metal Used for Upright Mast of Roadmaster Spare Tire Carrier # RM-195125

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching