How to Reset Breakaway Lever on Titan Model 6 Zinc-Plated Brake Actuator T4079200
Question:
How do you reset the break away lever on a Titan Zinc-Plated Brake Actuator - Drum - 2-5/16inch Ball - Bolt On
asked by: JAMES Z
Expert Reply:
On a Titan model 6 actuator like # T4079200 the breakaway reset procedures is as follows:
When the break-away lever is engaged, it is in the vertical position. It must be reset before the trailer is moved.
First, carefully loosen the pressure line fitting to the master cylinder to relieve hydraulic pressure. Then remove the four bolts that secure the master cylinder assembly to the outer case.
The flat front tab of the “U” shaped break-away spring can then be placed in the top notch of the break-away lever. Then position the back tab of the break-away spring on the top of the master cylinder mounting bracket as you line up the master cylinder assembly bolt holes.
Tighten the bolts and check the break-away lever position – it should be at about a forty five degree angle. Tighten the brake line fitting and re-bleed the brakes as necessary.
Product Page this Question was Asked From
Dexter Zinc-Plated Brake Actuator - Drum - 2-5/16" Ball - Bolt On - 8,000 lbs
- Brake Actuator
- Surge Brake Actuator
- Straight Tongue Coupler
- Bolt-On
- 8000 lbs GTW
- 2-5/16 Inch Ball Coupler
- Drum Brakes
- No Lockout
- Dexter
more information >
Continue Researching
- Shop: Dexter Zinc-Plated Brake Actuator - Drum - 2-5/16" Ball - Bolt On - 8,000 lbs
- Shop: Replacement Master Cylinder Assembly for Dexter Model 6 Brake Actuators - Drum
- Video: Titan Brake Actuator - Surge Brake Actuator - T4079200 Review
- Shop: Hydraulic Trailer Brake Kit - Uni-Servo - Free Backing - 10" - Left/Right Hand - 3,500 lbs
- Shop: Kodiak Hydraulic Brake Hose - 3/16" Male Fittings w/ Stainless Flares - 1/8" ID - 1'
- Video: Powerbuilt Tools - Vehicle Tools - ALL648591 Review
- Video: TruRyde Double Lip Grease Seals Review
- Shop: Hand Vacuum Pump Brake Bleeder
- Shop: Hydraulic Trailer Brake Kit - Uni-Servo - Dacromet - 10" - Left/Right Hand Assemblies - 3.5K
- Shop: Hydraulic Trailer Brake Kit - Uni-Servo - 10" - Left and Right Hand Assemblies - 3,500 lbs
- Search Results: dexter brake cylinder
- Search Results: dico master cylinder
- Search Results: dico 60
- Search Results: t1209800
- Search Results: dexter brake actuator
- Search Results: surge brake actuator
- Search Results: dexter surge brake actuator
- Video: Kodiak Trailer Brakes BH-3MFS-1 Review
- Q&A: Solution for Banging During Starts and Stops with Titan Model 6 Actuator on Trailer
- Article: Trailer Wiring Diagrams
- Video: Demco Trailer Brakes DM5403 Review
- Q&A: Replacement Actuator and Hydraulic Brake Lines for 1989 Escort Boat Trailer
- Q&A: Plumbling Hydraulic Brake Lines for Tri Axle Boat Trailer
- Video: HydraStar Hydraulic Brake Line Kit Review
- Video: Review of Hydrastar Trailer Brake Lines - HS496-253
- Q&A: How to Reset the Breakaway Lever on a Titan Model 6 Trailer Brake Actuator
- Q&A: How to Bleed Brake Lines with Titan Model 60 Hydraulic Brake Actuator Without Electric Lockout
- Q&A: Use of a P3 Brake Controller on 2005 Ford F-350 Instead of Factory Controller
- Q&A: Why is There a Wire Color Differnce Between 7 Way Traditional vs RV Standard