How To Service Landing Gear Legs On a 5th Wheel Trailer
Question:
How do we get the leg out to repair or replace parts?
asked by: Brenda T
Expert Reply:
The easiest option to replace or repair any parts in a landing gear setup would be to couple the trailer to the tow vehicle as this would then support the front of the trailer so you can make repairs as needed. If you are asking what needs to be done once the weight of the trailer is off the landing gear; the first step is to unbolt the motor, disconnect the intermediate shaft, remove the gearbox, and then undo the bolt for the weld stop brackets. Once the bolt is removed the landing gears should be able to be slide out towards the vehicle. I have attached a list of repair parts for you below as well.
Lead Jack Repair Kit for Stromberg Carlson Landing Gear part # LG-146059
Follow Jack Repair Kit for Stromberg Carlson Landing Gear part # LG-146060
Replacement Motor for Stromberg Carlson Electric Landing Gear part # LG-142178
Replacement Aluminum Gearbox for Stromberg Carlson Landing Gear part # LG-179015
Replacement Footpad and Pin for Stromberg Carlson Landing Gear part # LG-119225
Products Referenced in This Question
Replacement Footpad and Pin for Stromberg Carlson Landing Gear
- Accessories and Parts
- Camper Jacks
- Trailer Jack
- Jack Foot
- Stromberg Carlson
more information >
Replacement Motor for Stromberg Carlson Electric Landing Gear - 5,500 lbs
- Accessories and Parts
- Camper Jacks
- Trailer Jack
- Motor and Gear Parts
- Motor
- Stromberg Carlson
more information >
Lead Jack Repair Kit for Stromberg Carlson Landing Gear
- Accessories and Parts
- Camper Jacks
- Trailer Jack
- Hardware
- Repair Kit
- Stromberg Carlson
more information >
Follow Jack Repair Kit for Stromberg Carlson Landing Gear
- Accessories and Parts
- Camper Jacks
- Trailer Jack
- Hardware
- Repair Kit
- Stromberg Carlson
more information >
Replacement Aluminum Gearbox for Stromberg Carlson Landing Gear
- Accessories and Parts
- Camper Jacks
- Trailer Jack
- Motor and Gear Parts
- Gearbox
- Stromberg Carlson
more information >
Product Page this Question was Asked From
Stromberg Carlson Electric Landing Gear Set - Weld On - 34-7/8" Lift - 5,500 lbs
- Camper Jacks
- Fifth Wheel Camper
- Leveling Jacks
- Stabilizer Jacks
- Steel
- 5001 - 6000 lbs
- Electric Jack
- Landing Gear
- 35 Inch Lift
- Weld-On
- 2 Jacks
- Stromberg Carlson
more information >
Featured Help Information
Instructions
Continue Researching
- Q&A: Replacement Landing Gear for 2002 Carriage Cameo F34CK3 5th Wheel Trailer
- Q&A: Landing Gear Recommendation for a 2002 Carriage Cameo Fifth Wheel Model F34CK3
- Q&A: Replacement Landing Gear for a Keystone Laredo 5th Wheel Trailer
- Q&A: Troubleshooting Landing Gear on Fuzion Toy Hauler That Will No Longer Lift Trailer
- Q&A: Replacement Powered Landing Gear Setup for 2007 Keystone Laredo LA25RK07
- Q&A: Complete AC System With An Advent 13.5K BTU Low Profile AC Unit
- Q&A: Reese and B and W Fifth Wheel Hitch Solutions that Fit 2013 Chevy Silverado Short Bed 2500 Denali
- Article: Trailer Wiring Diagrams
- Article: Performance Chips and Modules
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Article: Stability Control for Heavy Duty Vehicles
- Article: What is Boondocking
- Article: Rooftop Cargo Carriers
- Article: How to Measure for Travel Trailer and Fifth Wheel Steps