Flared Adapter Availability from Camco Gen-Turi Transfer Kit # CAM44881

Question

Question:

Is the flared adapter in this kit available by itself? It fits over a 1 1/2inch exhaust pipe on the split end and the other end is where the Gen-Turi exhaust pipe inserts with the hitch pin.

asked by: Hilary

0

Expert Reply:

We do have just the coupler portion of the part # CAM44881 that you are looking for as the part # CAM44842.

expert reply by: Jameson C

0

Answer 1

Here are the inner and outer dimensions for the Camco Gen-Turi items you asked about. Part #CAM44872 – OD is 2.94 inches and ID on the small end is 2.69 inches. Part #CAM44862 – OD is 1.51 inches and ID is 1.25 inches on the flared end. No dimensions…

view full answer...

Answer 2

For your generator exhaust, the Camco Gen-Turi Replacement 30" EMT 90-Degree Discharge Pipe #CAM44812 is designed to be used with the Camco Gen-Turi RV Generator Exhaust System #CAM44461. With that being said, we have not tested the #CAM44812…

view full answer...

Answer 3

Since you have 6 wheels, the TireMinder Smart TPMS for RVs #TPMS-APP-4 that you mentioned will work, however you won't have enough sensors for all six tires. Instead, I recommend going with the: -TireMinder i10 TPMS for RVs and Trailers w/ Signal…

view full answer...

Answer 4

I recommend using a system like the TireMinder i10 TPMS for your 2018 Grand Design Momentum 5th wheel toy hauler. The TireMinder has a system with either 4 Sensors #TM89FR or 6 Sensors #TM29FR. The sensors are capable of detecting both tire pressure…

view full answer...

Answer 5

What you could do is use the 30 inch, 90 degree adapter for the Gen-Turi part #CAM44812 with the Gen-Ture part #CAM44461 to route the exhaust around the slide out.

view full answer...

Answer 6

The Camco Gen-Turi RV Generator Exhaust System #CAM44461 can use the Camco Suction Cup Mounts for Gen-Turi Exhaust System - Qty 2 #CAM44850 for simple mounting. This system uses slotted bushings for an integrated fit. It sounds like you also want the…

view full answer...

Answer 7

The smallest sleeve of the Camco Gen-Turi Transfer Kit, part #CAM44881, has an inner diameter of 1.23 inches and an outer diameter of 1.34 inches. It's 1-1/2 inches long. This is used to move the Gen-Turi RV Generator Exhaust System, part…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

You are correct that this refrigerator does not have an ON/OFF switch or function. The best you can do is "Standby" that draws an unknown amount of power. One option is to pull the 12-Volt fuse at the RV power center. A much better option…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Flared Adapter Availability from Camco Gen-Turi Transfer Kit # CAM44881

Continue Researching