Recommended Lift kit for a 2017 Lance 1475 Travel Trailer with Torflex Axle

Question

Question:

Is there a lift kit for a 2017 Lance 1475?

asked by: Alan G

0

Expert Reply:

Your 2017 Lance 1475 has a GVWR of 3,700 lbs so you will have the Dexter #10 torsion axle rated for 2300 to 4000-lbs and will want lift kit # K71-707-01. This will lift your trailer frame by 2-5/8 inches.

expert reply by: Jason S

0

Answer 1

From what I could find it looks like your 2017 Lance model 1475 has the Dexter #10 torsion axle. If that is the case, the Torflex Lift Kit #K71-707-01 is the correct lift kit for that axle. I recommend that you verify that is the axle that you have…

view full answer...

Answer 2

Your 2017 Lance 1475 has the Dexter #10 torsion axle. The lift kit for that axle is #K71-707-01 like you referenced and will give you a lift of 2-5/8 inches.

view full answer...

Answer 3

By "mobile home type bolt pattern" I believe you are talking about a 5 spoke utility bolt pattern such as what is on the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles #8-174-5UC3. To measure your axle from hub face to…

view full answer...

Answer 4

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 5

The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.

view full answer...

Answer 6

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Answer 7

The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.

view full answer...

Answer 8

Brake systems are not dependent on the hub bolt pattern. So you can use the Electric Trailer Brake Kit #AKEBRK-7-SA for 12 inch hub/drums or #AKEBRK-35-SA for 10 inch hub/drums. Then use #10-1-1 wire sold by the foot for your brake magnet wiring.…

view full answer...

Answer 9

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 10

The Tekonsha OEM Vehicle Wiring Harness #22121 that you referenced includes all the wiring and parts necessary to install a fully functional 7-Way connector and trailer brake controller. The included brake controller harness is compatible with and…

view full answer...

Answer 11

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 12

Normal operating temperatures for drum brakes range from 150-400 degrees F. During certain stopping conditions the brake heat can exceed 600 degrees. The effectiveness and stopping power of the brakes is significantly reduced at these higher…

view full answer...

Recommended Lift kit for a 2017 Lance 1475 Travel Trailer with Torflex Axle

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching