How to Pick Out Replacement Landing Gear for 1998 Alumascape 5th Wheel
Question:
Need to replace the jacks. A shop looked the unit over before I purchased it, they bent a stand and replaced it with another one that doesn’t line up with the other side. The bar between them appears to be slightly bent. The motor works ok for a few seconds but then it starts slipping and it must be hand cranked, which is very difficult. I can’t get to my door because it’s too close to the fence, and I can’t move it. Can you tell me what I need to order?
asked by: Jewell
Expert Reply:
In order to pick out a direct replacement for the landing gear on your trailer we would need to know the distance between the mounting brackets. Otherwise you could just have the brackets removed from your trailer by a qualified welder and then install the brackets that come with the Bulldog Tandem Landing Gear Set # BD500162. Either way this landing gear set would work well for you, you just might have to have the brackets of your trailer removed and then install the brackets of the # BD500162.
I attached a picture that shows the dimensions that this landing gear set would fit with.
The jacks would be the correct replacement for Lippert, Venture, and Atwood landing gear, as well as those from a few other manufacturers. The sure way to tell is that if the distance between the mounting brackets (underside of top bracket to top of lower bracket as shown in the diagram) is 17-1/2 inches. If this is the case, the landing gear should fit just fine. This is by far the most popular setup seen on trailers.
If your frame clamps are instead 20-1/4 inches the Ultra Fab part # UF17-943010 would be a direct replacement.
Products Referenced in This Question
Bulldog Tandem Landing Gear Set - Drop Leg - 36" Lift - 8,000 lbs
- Camper Jacks
- Fifth Wheel Camper
- Leveling Jacks
- Stabilizer Jacks
- Steel
- 7001 - 8000 lbs
- Landing Gear
- Sidewind Jack
- 36 Inch Lift
- Bolt-On
- 2 Jacks
- Bulldog
more information >
Ultra-Fab Deluxe Electric Landing Gear Set - 38" Lift - 12,000 lbs
- Camper Jacks
- Fifth Wheel Camper
- Leveling Jacks
- Stabilizer Jacks
- Steel
- 10001 lbs or More
- Electric Jack
- Landing Gear
- 38 Inch Lift
- Weld-On
- 2 Jacks
- Ultra-Fab Products
more information >
Product Page this Question was Asked From
Landing Gear Set w/ Handle - 36-1/2" Lift - 8,000 lbs
- Camper Jacks
- Fifth Wheel Camper
- Leveling Jacks
- Stabilizer Jacks
- Steel
- 7001 - 8000 lbs
- Landing Gear
- Sidewind Jack
- 36 Inch Lift
- Weld-On
- 2 Jacks
- etrailer
more information >
Featured Help Information
Instructions
Continue Researching
- Q&A: Bracket Dimensions of the etrailer RV Landing Gear System # RVLG-8HDL
- Q&A: Determining The Correct Replacement Landing Gear Set For A 1997 Forest River Sierra
- Q&A: How to Know if Landing Gear Set # RVLG-8HDL Will Fit 2001 Sunnybrook 31BWFS
- Q&A: Replacement Crank Handle for Ram 5th Wheel Landing Gear Compatibility With 2007 Fleetwood Nitrous TT
- Q&A: How to Choose the Correct Replacement Landing Gear for 5th Wheel Trailer
- Q&A: Are Replacement Parts for Atwood Landing Gear Available or Will Another Brand Fit
- Q&A: How to Measure to Pick Out Replacement Landing Gear for a Trailer
- Article: Trailer Wiring Diagrams
- Article: Most Popular Wheel Bearings
- Article: Stability Control for Heavy Duty Vehicles
- Article: How Much Solar Power Do I Need For My RV?
- Article: Best Camper Jacks
- Article: Where to Position the Trailer Axle?
- Article: Does Solar Panel Type Really Matter?