Diameter of Output Shaft on the MaxxAir Mini Deluxe Trailer Roof Vent

Question

Question:

Is the motor on the MaxxAir vent 3/32inch round bore or 1/8inch D-bore?

asked by: Blake

0

Expert Reply:

The output shaft on the fan motor within the MaxxAir Mini Deluxe Trailer Roof Vent part # MA00-03851 has a d-shape and is 1/8" diameter.

expert reply by: Conner L

0

Answer 1

The black top of the MaxxAir Mini Deluxe Trailer Roof Vent w/ 12V Fan #MA00-03851 is just under 4 inches tall so with the white base and black top combined, it will sit about 4-1/8 inches above the roof. I've attached a video to help with…

view full answer...

Answer 2

The Replacement MaxxFan Plus 4-Speed Roof Vent with White Lid #MA00-04751KSX is meant to be a direct replacement however not all the necessary hardware is included. The remaining items you'll need is the Key Wall Control part #MA00A03550K,…

view full answer...

Answer 3

In regards to installing a roof vent like the MaxxAir Mini Deluxe Trailer Roof Vent part #MA00-03851, the white trim piece that connects the top and bottom of the vent is called the garnish and this will be trimmed to fit the exact thickness of…

view full answer...

Answer 4

With a weight distribution system, you want to choose a system based on the fully loaded and ready to tow tongue weight of the trailer. I'll link you to a help article that explains how to determine your fully loaded tongue weight, but…

view full answer...

Answer 5

Believe it or not, the outside diameter of the Bearing Buddy is designed to be a bit larger than the inside diameter of the hub bore. Typically, a Bearing Buddy sized to fit a 1.98 hub bore will actually be about 1.986 in diameter, which means…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Diameter of Output Shaft on the MaxxAir Mini Deluxe Trailer Roof Vent

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching