Hitch Pin to Fit 2 Inch Class III Trailer Hitch on a Hummer H3
Question:
My order is scheduled to arrive on monday. didnt think to order a pin when I ordered the hitch. What size pin do I need to get the the hitch?
asked by: Jesse C
Expert Reply:
The hitch you ordered is the Draw-Tite # 75382 which is a 2 inch Class III receiver. For a standard hitch pin and clip use part # PC3. If you prefer a locking pin part # e98882 will fit the hitch.
I've also linked our complete selection of ball mounts that fit. One I like to recommend is the B&W Tow & Stow, part # BWTS10037B. It's adjustable with two different ball sizes so it can be used with a large variety of trailers. It also flips under itself to a stored position to keep it out of the way when you're not using it. If you go with the Tow & Stow I definitely recommend the locking hitch pin to keep it safe.
I've attached some articles and videos you might find helpful. Including one on the installation of the hitch.
Products Referenced in This Question
B&W Tow & Stow 2-Ball Mount - 2" Hitch - 5" Drop, 5-1/2" Rise - 10K - Black
- Trailer Hitch Ball Mount
- Adjustable Ball Mount
- 2 Inch Ball
- 2-5/16 Inch Ball
- Two Balls
- Steel Ball
- Steel Shank - Matte Black
- Drop - 5 Inch
- Rise - 5 Inch
- Fits 2 Inch Hitch
- 10000 lbs GTW
- Class IV
- B and W
more information >
etrailer Trailer Hitch Receiver Lock for 2" Hitch - Flush - 2-5/8" Span - Stainless Steel
- Trailer Hitch Lock
- Standard Pin Lock
- Keyed Alike
- Stainless Steel
- Fits 2 Inch Hitch
- Flush Pin
- 2-5/8 Inch Span
- etrailer
more information >
Pin and Clip for 2" and 2-1/2" Hitches - 5/8" Diameter x 3-1/4" Span
- Hitch Pins and Clips
- Standard Hitch Pin
- Fits 2 Inch Hitch
- Fits 2-1/2 Inch Hitch
- 5/8 Inch Diameter
- 4 Inch Span
- Draw-Tite
more information >
Product Page this Question was Asked From
Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 500 lbs TW
- 5000 lbs GTW
- 5000 lbs WD GTW
- 2 Inch Hitch
- 500 lbs WD TW
- Concealed Cross Tube
- Draw-Tite
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Q&A: How to Determine Where the Curt Hitch 14080 Will Install In Relation to Rear Bumper
- Q&A: Hitch Clearance On A 1996 GMC Yukon With Roll Pan
- Q&A: Bolt Hole Dimensions for Curt Trailer Hitch Receiver # 14080
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: How to Measure for Trailer Hitch Drop
- Q&A: Can a 2018 Jeep Renegade Manual Transmission with 4WD be Flat Towed?
- Q&A: Parts Needed To Flat-Tow a 2020 Chevy Colorado
- Article: How to Choose the Right Trailer Hitch Class
- Article: How to Choose a Spare-Tire-Bike Rack
- Q&A: Comparing Curt and Draw Tite Hitches for 2008 Hummer H3