Is there a Torque Spec for Installation of Castle Nut on 2,000 lb Axle?
Question:
I was wondering what the torque specs are for this bearing as I am trying to have it where the bearing wont go bad within a few uses. If there is any way you guys could help me it would be greatly appreciated. Thank you for taking the time to read this and or respond.
asked by: Christian T
Expert Reply:
The castle nuts do not have a torque spec. Bearings and races are fit to the spindle precisely and will have minimal movement to the washer and castle nut which will simply be tightened and held in place with the cotter pin # 165649. We recommend tightening until the nut stops without added force and then backing it off one notch to fit the castle nut.
The Dexter Trailer Idler Hub Assembly for 2,000-lb Axles - 4 on 4 - L44649 Bearings # 8-91-05UC1 is a fit for 1.063 inch spindles and when the grease is packed into the bearings correctly will prevent the bearings from failure. I recommend using the Bearing Packer - Plastic # PTW1218 to ensure proper preparation use grease.
Products Referenced in This Question
Cotter Pin - 1/8" Thick x 1-3/4" Long
- Accessories and Parts
- Trailer Leaf Spring Suspension
- Cotter Pin
- ABS Fasteners
more information >
Product Page this Question was Asked From
Dexter Trailer Idler Hub Assembly for 2,000-lb Axles - 4 on 4 - L44649 Bearings
- Trailer Hubs and Drums
- Hub
- Standard
- L44649
- L44649
- For 2000 lbs Axles
- 4 on 4 Inch
- 10 Inch Wheel
- 12 Inch Wheel
- Dexter
more information >
Continue Researching
- Search Results: sway control
- Shop: Bearing Packer - Plastic
- Search Results: break away kit
- Shop: Curt Push-To-Test Trailer Breakaway Kit with Built-In Battery Charger - Side Load
- Shop: Ladder Rack
- Shop: Trailer Axle with Idler Hubs - 5 on 4-1/2 Bolt Pattern - 72" Long - 2,000 lbs
- Q&A: Replacement Seals and Castle Nut for 2000-lb Dexter Axle with EZ-Lube Spindles and 5-Lug Hubs
- Q&A: What Size Socket Works with 1 Inch Spindle Castle Nut # 165686?
- Shop: Trailer Spindle Nut 1"
- Shop: Curt Towing Starter Kit for 1-1/4" Hitches - 2" Ball - 3/4" Rise - 3,500 lbs
- Shop: Dexter Electric Trailer Brakes - 7" - Left/Right Hand Assemblies - 2,000 lbs to 2,200 lbs
- Shop: Replacement Sway Control Tab for Weight Distribution System - Weld On
- Video: Performance Tool Plastic Bearing Packer Review
- Search Results: trailer brake wire
- Search Results: bearing packer
- Search Results: akihub~545~2~2k
- Search Results: breakaway
- Search Results: breakaway cable
- Video: Draw-Tite Electric Trailer Brake Controller Wiring Kit Review
- Video: Review of Dexter Axle Trailer Brakes - RH and LH 7 Inch Electric Drum Brakes - 23-47-48
- Q&A: How to Determine if 2,000 lb Capacity Hub and Drum and Electric Brakes Will Fit
- Q&A: Parts Needed to Add Electric Drum Brakes to a 5 x 8 Utility Trailer
- Q&A: Recommended Lug Nut Torque Rating on 2,000lbs Trailer Hub Assembly # 34822BX
- Shop: Roof Rack
- Q&A: How Long Do the Wheel Bearings Last in the Yakima Rack and Roll Trailer
- Video: Review of Yakima Replacement Tongue Wiring Harness For Rack And Roll Trailer - Y8880203
- Video: Yakima Roof Rack - Crossbars - Y00411 Review
- Video: Yakima Rack and Roll Trailer Assembly
- Video: Review of DeeMaxx Trailer Bearings Races Seals Caps - Stainless Steel Cap with Plug - DE69YR
- Article: 7 Common Questions Everyone Has About Trailer Tires