Correct Bearing Buddy for the Trailer Idler Hub Assembly Part # AKIHUB-440-2-2K
Question:
the bearing buddies were the correct size. The one issue I do have is that the grease seal that was shipped did not fit the spindle, the interior dimension was too big. Based on the spindle width and the existing bearings I had (L44649) all indications led me to believe 1.06 was the correct size which it appears to be. Just not the grease seal. Can you send me the correct seal?
asked by: Chris
Expert Reply:
Yes, the correct Bearing Buddy Bearing Protectors for the Trailer Idler Hub Assembly part # AKIHUB-440-2-2K is part # BB1980A-SS for stainless steel or part # BB1980A for chrome plated.
Products Referenced in This Question
Double Lip Grease Seal - ID 1.249" / OD 1.983" - Qty 1
- Trailer Bearings Races Seals Caps
- Seals
- Grease Seals - Double Lip
- 1.249 Inch I.D.
- 1.983 Inch O.D.
- TruRyde
more information >
Bearing Buddy Bearing Protectors - Model 1980A w/ Auto Check - Chrome Plated (Pair)
- Trailer Bearings Races Seals Caps
- Caps
- Bearing Protector Grease Cap
- 1.98 Inch
- Bearing Buddy
more information >
Bearing Buddy Bearing Protectors - Model 1980A-SS w/ Auto Check - Stainless Steel (Pair)
- Trailer Bearings Races Seals Caps
- Caps
- Bearing Protector Grease Cap
- 1.98 Inch
- Bearing Buddy
more information >
Product Page this Question was Asked From
Trailer Idler Hub Assembly for 2,000-lb Axles - 4 on 4 - L44649 Bearings - Pre-Greased
- Trailer Hubs and Drums
- Hub
- Pre-Greased
- Standard
- L44649
- L44649
- For 2000 lbs Axles
- 1/2 Inch Stud
- 4 on 4 Inch
- 8 Inch Wheel
- 10 Inch Wheel
- 12 Inch Wheel
- 13 Inch Wheel
- 14 Inch Wheel
- etrailer
more information >
Continue Researching
- Q&A: What Is the Difference Between a BTR and BT8 Spindle
- Q&A: How to Tell if Trailer has a BT8 or BTR Spindle Installed
- Q&A: Solution for Replacement Hubs on Northern Tool Ultra-Tow 49803 Aluminum Trailer
- Q&A: Correct Replacement for Dexter Hub/Drum 8-415
- Article: Most Popular Wheel Bearings
- Q&A: Replacement Hub Needed for Lippert 122093 Hub on 5,200 lbs Axle
- Article: Trailer Tire Sizing
- Q&A: What is the Difference Between Load Range C and Load Range D Tires
- Q&A: What is the Difference Between Load Range C and D ST175/80D13 Trailer Tires
- Article: How to Measure a Trailer Axle
- Article: 7 Common Questions Everyone Has About Trailer Tires
- Article: Replacing the Bearing, Races and Seals on a Trailer Hub
- Article: How to Bleed Your Trailer Surge Brakes
- Article: 2023 Best Gifts for RVers & Campers
Chris
10/18/2018
the bearing buddies were the correct size. The one issue I do have is that the grease seal that was shipped did not fit the spindle, the interior dimension was too big. Based on the spindle width and the existing bearings I had (L44649) all indications led me to believe 1.06 was the correct size which it appears to be. Just not the grease seal. Can you send me the correct seal?