Powering Interior Trailer Lights Using a Battery Instead of Trailer Connector
Question:
Greetings - I have a newer Pace American 14foot cargo trailer that has two interior dome lights but they only work if the 7 pin connector is plugged into the tow vehicle Toyota 4runner and the tow vehicle is running or key left in start position which activates all the dash lights and drains the vehicles battery over time. My goal is to make the dome lights work independent of the tow vehicle while I use the trailer for camping. The trailer has a small 12v battery to support the breakaway trailer function. Can I use that to power the interior lights ? Do you have a wiring diagram for a Pace trailer so I can identify the interior lights circuit and make the connection?
asked by: Thomas
Expert Reply:
The breakaway battery should only be used to power the trailer brakes in a breakaway event so I strongly recommend using a separate 12 volt battery to power the interior lights in your trailer. Since the lights currently run off of the 12 volt circuit you can trace the 12 volt wire from the trailer connector to where it enters the trailer. That is likely the wiring for the lights.
If you were to wire a battery to that wire and put a switch in line such as # PK34513 you would be good to go!
We do not have access to the wiring diagram for your Pace trailer.
Products Referenced in This Question
Pollak Light-Duty Toggle Switch - On-Off - 12 Volt - 10 Amp - 6" Wire Leads
- Accessories and Parts
- Wiring
- Switches
- Toggle Switch
- 10 Amp
- Pollak
more information >
Product Page this Question was Asked From
Pollak Black Plastic, 7-Pole, RV-Style Trailer Connector - Trailer End
- Trailer Wiring
- Trailer Connectors
- Trailer End Connector
- Plug Only
- 7 Round - Blade
- Pollak
more information >
Continue Researching
- Shop: etrailer Electric Trailer Brakes w/ Dust Shields - Self-Adjusting - 12-1/4" - Left/Right - 10K
- Q&A: How to Power Trailer Dome Light When Not Connected to Tow Vehicle
- Shop: Trailer Wiring
- Shop: Vehicle Cargo Control
- Shop: Truck Bed Sliding Tray
- Q&A: How To Install The Custom Third Brake Light Camera For 8" Monitor On 2021 Ford Super Duty
- Q&A: Wiring in an LED Work Light and Switch to a Trailers Running Light Circuit
- Shop: Pollak Light-Duty Toggle Switch - On-Off - 12 Volt - 10 Amp - 6" Wire Leads
- Shop: Oil Seal
- Shop: Oil Seal
- Shop: Trailer Hub Grease Cap with Rubber Plug, 2.72" - Drive-In for EZ Lube Axles - Qty 1
- Shop: Dexter Tang Washer - Type B
- Shop: Mounting Bolts and Hardware for 12-1/4" Brake Assemblies - 10,000 lbs to 15,000 lbs
- Video: Pollak Light-Duty On-Off Toggle Switch Installation
- Q&A: How To Install a 30 Amp Service on an Enclosed Cargo Trailer
- Shop: Towing Mirrors
- Q&A: Options for Adding Interior Lighting to Enclosed Cargo Trailer
- Q&A: Solution for Replacing OEM 7-Way With EZ Connector on 2020 Toyota Tundra
- Q&A: Can Trailer Lights be Powered When Not Connected to Tow Vehicle
- Article: Trailer Wiring Diagrams
- Shop: Suspension Enhancement
- Video: Review of SuperSprings Vehicle Suspension - Rear Axle Suspension Enhancement - SS45MR
- Video: Pollak Wiring - Wiring Adapters - PK11896 Review
- Video: Review of Progressive Dynamics RV Converters - Power Converter W Charge System - PD4045KA
- Video: etrailer E-Track Systems Roller Idler Review
- Article: How Much Solar Power Do I Need For My RV?
- Search Results: cooler
- Search Results: trailer backup camera